Table of Contents
Advertisement
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Observe all governing codes and ordinances.
Required:
■ A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
■ A time-delay fuse or time-delay circuit breaker.
■ A separate circuit serving only this microwave oven.
OPERATING YOUR MICROWAVE OVEN
Settings
Clock
The Clock is a 12-hour (12:00-11:59) or 24-hour (0:00-23:59)
clock. Touch OPTIONS/CLOCK to reach Clock submenu,
and follow the prompts to set the Clock. Clock format
(12 hours with AM and PM, 12 hours without AM and PM
or 24 hours) may also be set in the Clock submenu.
Timer
With the microwave oven in standby mode, touch the Timer
control, enter time, then touch the Timer control or the Start
control. Cook functions may be entered while the Timer
is counting down. To cancel timer, touch Timer control while
the Timer countdown is active in the display.
Control Lock
Activate to avoid unintended start. Touch and hold the Cancel
control for about 3 seconds until 2 tones sound and padlock
icon appears in the display. Repeat to unlock control.
Options/Clock
Ten options/settings may be adjusted: 1-Clock & Energy Save;
2-Scrolling Speed; 3-Sound; 4-Language; 5-Auto Vent Fan;
6-Filter Reset; 7-Fan Timer; 8-Light Timer; 9-Demo Mode;
10-Factory Reset.
Vent Fan
Various speeds, ranging from High to Low, and Off. Comes
on automatically as cooling fan during any cook function.
Vent Timer: Set vent fan to run for exactly 30 minutes,
or to run for only 30 minutes more (off after 30 minutes).
The vent fan may be turned off at any time using the Vent
Fan control. Touch OPTIONS/CLOCK to reach the Fan Timer
submenu, and select the setting.
GROUNDING INSTRUCTIONS
For all cord connected appliances:
I
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
WARNING:
Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.
SAVE THESE INSTRUCTIONS
This device complies with Part 18 of the FCC Rules.
Auto Vent Fan (on some models): To keep the microwave
oven from overheating, the auto vent fan will automatically turn
on at high speed if the temperature from the range or cooktop
below the microwave oven gets too hot. When this occurs,
the vent fan cannot be turned off. "AUTO FAN ON for heat
circulation" appears in the display.
Dynamic Fan Sensing (on some models): To keep
the microwave oven from overheating, the auto vent fan
will automatically turn on at various speeds, depending
on the temperature from the range or cooktop below the
microwave oven. When this occurs, the vent fan cannot
be turned off. "AUTO FAN Sensor Technology for heat
circulation" appears in the display. As the temperature cools,
the fan will automatically decrease its speed, then turn off.
Light Timer
Set the cooktop light to turn on and off at certain times.
Touch OPTIONS/CLOCK to reach the Light Timer submenu,
and follow the prompts to set the light on time and light
off time in hours and minutes, or to cancel Light Timer.
NOTE: Light Timer uses 12-hour clock only.
Filter Reset
Reset the filter status after replacing and/or cleaning the filters.
Touch OPTIONS/CLOCK to reach the Filter Reset submenu,
and activate reset.
Sound (Tones)
Programming tones and signals. Programming tones
may be turned off, or all tones (including end-of-function
signals) may be turned off. Touch OPTIONS/CLOCK to reach
the Sound submenu, then follow the prompts to turn off or
on the programming tones or all tones.
3
Advertisement
Table of Contents
