Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Innodisk EGP2 Series
Summary of Contents for Innodisk EGP2 Series
- Page 1 EMP2/EGP2 SERIES mPCIe/M.2 to Serial COM User Manual Rev 1.5...
- Page 2 Copyright Information 2005-2018 ©Innodisk Corporation. All Rights Reserved Innodisk™ is trademark or registered trademark of Innodisk Corporation. This document is subject to change and revision without notice. No part of this document may be reproduced in any form by any photographic, electronic, mechanical or other means, or used in any information storage and retrieval system, without prior written permission from Innodisk Corporation.
- Page 3 2005-2017 © Innodisk Corporation. All Rights Reserved Revision History Revision Date Description 2015/10/21 Initial Release Add products of EMP2-X4S1& EMP2-X4S2 2016/10/4 Remove EMP2-X401 2017/05/31 2017/11/30 1. Add the product of EGP2-X401 2. Add a NOTE of Windows embedded in section 1.1.
-
Page 4: Table Of Contents
2005-2017 © Innodisk Corporation. All Rights Reserved Table of Contents Revision History ........................ii Table of Contents ....................... iii Overview ..........................1 Windows ......................... 2 1.1. Install Driver ......................2 1.2. Switch Mode by Software (for EMP2-X404/X801, EGP2-X401) ......... 4 1.3. -
Page 5: Overview
2005-2017 © Innodisk Corporation. All Rights Reserved Overview This manual describes how to implement EMP2 mPCIe to serial COM cards of the following products. Product No. RS232 RS485HD RS485FD Switch Method EMP2-X202 Hardware EMP2-X402 Hardware EMP2-X203 EMP2-X403 EMP2-X801 Software EMP2-X404... -
Page 6: Windows
2005-2017 © Innodisk Corporation. All Rights Reserved Windows 1.1. Install Driver This section is applicable to ALL products. Please notice that the driver name including “Adj” is for EMP2 -X404/X801 and EGP2-X401. The driver name including “Fixed” is for EMP2-X202/X203/X402/X403/X4S1/X4S2. - Page 7 2005-2017 © Innodisk Corporation. All Rights Reserved NOTE1: If you encounter an error while executing the driver, please download “Microsoft Visual C++ Redistributable Package” then install first. https://www.microsoft.com/en-us/download/details.aspx?id=29 NOTE2: Please confirm Window Embedded has included “windows generic multifunction card driver” inbox driver.
-
Page 8: Switch Mode By Software (For Emp2-X404/X801, Egp2-X401)
2005-2017 © Innodisk Corporation. All Rights Reserved 1.2. Switch Mode by Software (for EMP2-X404/X801, EGP2-X401) This section is applicable to following products. Product No. RS232 RS485HD RS485FD Switch Method EMP2-X404 Software EMP2-X801 Software EGP2-X401 Software In Device Manager, right click the mouse to enter “properties” in... - Page 9 2005-2017 © Innodisk Corporation. All Rights Reserved In “COM Settings”, you can select different mode among RS232, Loopback, RS485HD and RS485FD.
-
Page 10: Switch Mode By Hardware (For Emp2-X202/X402)
Please refer to the following picture: 1.4. Enable RS-485 checkbox for RS-485 Half/Full Duplex Mode This section is applicable to ALL products. In Device Manager, right click the mouse to enter “properties” in “Innodisk’s Communications Port (COM“N”)”. (“N” depends on the setting of real environment.) In “Port Settings”, please check RS-485 checkbox when using RS-485 Half... -
Page 11: Linux
2005-2017 © Innodisk Corporation. All Rights Reserved Linux Here we use Ubuntu 14.04 for example. 2.1. Install Driver This section is applicable to ALL products. Step1. Go to driver folder. Step2. Type command “make”. Step3. Type command “sudo make install”... -
Page 12: Switch Mode By Software (For Emp2-X404/X801, Epg2-X401)
2005-2017 © Innodisk Corporation. All Rights Reserved 2.3. Switch Mode by Software (for EMP2-X404/X801, EPG2-X401) This section is applicable to following products. Product No. RS232 RS485HD RS485FD Switch Method EMP2-X404 Software EMP2-X801 Software EGP2-X401 Software After installing driver and control tools, you can simply execute below command to initial EMP2 device. -
Page 13: Switch Mode By Hardware (For Emp2-X202/X402)
2005-2017 © Innodisk Corporation. All Rights Reserved COMMAND: emp2init reset Reset all port to default mode RS232. 2.4. Switch Mode by Hardware (for EMP2-X202/X402) Please follow instructions in 1.3. Switch Mode by Hardware to configure DIP switch. This section is applicable to following products. -
Page 14: Contact Us
2005-2017 © Innodisk Corporation. All Rights Reserved Contact us Headquarters (Taiwan) 5F., No. 237, Sec. 1, Datong Rd., Xizhi Dist., New Taipei City 221, Taiwan Tel: +886-2-77033000 Email: sales@innodisk.com Branch Offices: usasales@innodisk.com +1-510-770-9421 Europe eusales@innodisk.com +31-40-3045-4008 Japan jpsales@innodisk.com +81-3-6667-0161 China sales_cn@innodisk.com...
Need help?
Do you have a question about the EGP2 Series and is the answer not in the manual?
Questions and answers