General Information ... Information on protection of the environment ... Before using the appliance for the first time ... Safety Instructions ... Intended use ... Technical safety ... Special information for gas cookers ... Proper use ... Correct installation ... Operating modes ...
General information NFORMATION ON PROTECTION OF THE ENVIRONMENT Disposal of transport packaging Your new appliance was sent to you in protective packaging. All utilised materials are environmentally safe and recyclable. Please help us by disposing of the packaging in an environmentally friendly manner.
Intended use This extractor hood complies with the stipulated safety regulations. Improper use may result in injury or damage. The extractor hood may be used in the household only. The manufacturer is not liable for damage which is caused by improper use or incorrect operation.
Safety instructions Safe operation is possible provided the low pressure in the installation room of the heating appliance does not exceed 4Pa (0.04mbar). This can be achieved if the combustion air can flow through non-closable openings, e.g. in doors, windows, in conjunction with air intake/exhaust air wall boxes or by other technical measures.
Proper use Clean the extractor hood thoroughly before using for the first time. Before cleaning and servicing the extractor hood, isolate it from the power supply by pulling out the mains plug or switching off the fuse. Bulbs (especially halogen bulbs) become very hot during operation.
Operating modes The extractor hood can be used in exhaust air and circulating air mode. Exhaust-air mode The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system. Circulating-air mode The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen.
On/Off The appliance is operated by gently the tapping the sensor buttons. NOTE: It is recommended to switch on the blower when you start cooking and not to switch it off again until several minutes after you have finished cooking. In this way the kitchen fumes are removed most effectively.
Page 10
Operation On/Off Light The light can be switched on and off independently of the fan. To adjust the luminosity, hold down the button until the required luminosity is obtained. Switching the acoustic signal off and on When a button is pressed, an acknowledgement signal sounds.
OOKING AFTER THE APPLIANCE Suitable cleaning agents and care products for your appliance can be purchased via the Hotline or from the Online Shop (see cover page). Appliance surfaces NOTE: Observe the warranty regulations in the enclosed service booklet. The appliance surfaces and controls are scratch-sensitive.
Removing and installing the grease filters Before removing and installing the grease filters, always follow the instructions and warnings in the chapter entitled ”Safety instructions”! Removing and installing the metal-mesh grease filters 1. Open the lock and fold down the grease filters.
Before changing the bulbs, always follow the instructions and warnings in the chapter entitled ”Safety instructions”! The description of changing the bulbs applies to several appliance models. NOTE: Observe the warranty regulations in the enclosed service booklet. Changing the halogen bulbs Halogen bulbs become very hot during operation.
Installation instructions Prior to installation, always follow the instructions and warnings in the chapter entitled ”Safety instructions”! Exhaust-air mode The exhaust air is conveyed upwards via a ventilation shaft or directly through the outer wall to the exterior. NOTE: The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms which contain heating...
LECTRICAL CONNECTION Before connecting the appliance to the power supply, always follow the instructions and warnings in the chapter entitled ”Safety instructions”! The extractor hood may only be connected by a qualified electrician who is familiar with the regulations of the relevant electricity supply company.
Installation The extractor hood is designed to be mounted on the wall. During installation, optional accessories may also require fitting. Observe the minimum distance between hob and extractor hood (see ”Safety instructions”)! Avoid damaging the sensitive surfaces! Preparing the wall RISK OF INJURY, DAMAGE TO PROPERTY Before drilling the holes for the designated...
Attachment and alignment 1. Initially remove the protective foil from the back of the extractor hood and, following installation, remove foil completely. Mount the extractor hood, ensuring that the back is attached firmly to the brackets 3. Align the extractor hood horizontally by turning the brackets..
Installation Installing the flue ducts 1. Unscrew the cover. 2. Insert flue duct at an angle into the groove on the extractor hood and tilt backwards. 3. Insert side decor panels. 4. Insert both brackets and screw tight.
Page 19
5. Insert fluorescent tubes. 6. Connect the power to the fluorescent tubes. klick! RISK OF INJURY Ensure that the power cable is secure. 7. Insert fluorescent tubes all the way and screw tight. 8. Connect to the power supply (see ”Electrical connection”).
Need help?
Do you have a question about the DWB099752B and is the answer not in the manual?
Questions and answers