Childproof Lock; Changing The Basic Settings; Cleaning System; Before Cleaning - Bosch HBG53R560B Instruction Manual

Childproof lock

The oven has a childproof lock to prevent children switching it
on accidentally.
The oven will not react to any settings. The timer and clock can
also be set when the childproof lock has been activated.
If the type of heating and temperature or grill setting have been
set, the childproof lock interrupts the heating.
Activating the childproof lock
No cooking time or end time should have been set.

Changing the basic settings

Your oven has various basic settings. These settings can be
customised to suit your requirements.
Basic setting Selection 1 Selection 2 Selection 3
c1 Clock display always*
c2 Signal duration approx.
upon completion of 10 seconds
a cooking time or
timer period
c3 Waiting time until a approx.
setting is applied 2 seconds
* Factory setting

Cleaning system

The cleaning system regenerates the self-cleaning surfaces in
the cooking compartment.
The back wall, ceiling and side walls of the cooking
compartment are coated with a highly porous ceramic layer.
This coating absorbs and disintegrates splashes from baking
and roasting while the oven is in operation. If these self-
cleaning surfaces no longer clean themselves adequately, they
can be regenerated with the cleaning system.

Before cleaning

Remove accessories and cookware from the cooking
compartment.
Cleaning the cooking compartment floor
Before you set the cleaning system, clean the surfaces in the
cooking compartment that are not self-cleaning. Otherwise,
stains will develop that it is not possible to remove.
Use a dish cloth and hot soapy water or a vinegar solution. If
there are heavy deposits of dirt, use a stainless steel scouring
pad or oven cleaner. Only use when the cooking compartment
is cold. Never treat the self-cleaning surfaces with a scouring
pad or oven cleaner.

Making settings

Cleaning takes approximately one hour.
Set the function selector to
1.
Set the temperature selector to
2.
Press the button.
u
3.
The symbol lights up in the display. The time at which the
u
cleaning will end appears and the
only with -
the 0 but-
ton
approx. approx.
2 minutes* 5 minutes
approx. approx.
5 seconds* 10 seconds
< 3D hot air.
.
s
symbol is in brackets.
p
Press and hold the D button for approx. four seconds.
The symbol appears in the display. The childproof lock is
D
activated.
Deactivating the childproof lock
Press and hold the button for approx. four seconds.
D
The D symbol goes out in the display. The childproof lock is
deactivated.
No other time-setting option should have been set.
Press and hold the 0 button for approx. 4 seconds.
1.
The current basic setting for the clock display is shown in the
display, e.g. c1 1 for selection 1.
Use the @ or A button to change the basic setting.
2.
Confirm by pressing the
3.
The next basic setting appears in the display. You can scroll
through all levels with the
with the or button.
@ A
To finish, press and hold the
4.
All basic settings are applied.
You may change the basic settings at any time.
Cleaning will start after a few seconds. You will see the time
counting down and the
r
symbol goes out.
Cleaning is finished
A signal sounds. The oven stops heating. 00:00 is shown in the
display. Press the button twice and turn the function selector
0
to the off position. The oven switches off.
Cancelling cleaning
Press the button and turn the function selector to the off
u
position. The oven switches off.
Setting a later end time
You can delay the time at which the cleaning programme is due
to finish. For instance, you can set the cleaning programme to
run at night so that you can use your oven during the day.
Make the settings as described in steps 1 to 3. Before cleaning
starts, use the or button to set a later end time.
@ A
The oven switches to standby. The display shows the time at
which the cleaning will finish and the
When cleaning starts, you can see the time counting down in
the display and the symbol is in brackets. The
r
goes out.

After cleaning

When the cooking compartment has cooled down completely,
wipe the salt residues off the self-cleaning surfaces with a
damp cloth.
button.
0
0 button and change the setting
0 button for approx. 4 seconds.
symbol will be in brackets. The
symbol is in brackets.
p
p
p
symbol
11