Table of Contents
Advertisement
Steam Drying - Steam Refresh
Steam Drying - Steam Refresh
Steam programmes for unwrinkling or refreshing
Your water tank empties automatically after the programme has finished.
– Your dryer has unwrinkling and refreshing programmes that can be used for reducing
odours and minimising creasing in dry fabrics. Steam smooths and freshens up items of
Filling the water tank:
clothing.
– Sorting the laundry according to size, weight, fabric and colour is necessary.
Fill the dryer's water tank with distilled water before every Steam Dry - Steam Refresh cycle.
– Only use Short spin/Refresh for fabrics with the same properties.
– During steam generation (required), additional noises may occur.
1. Move the programme selector to Steam Dry
– The result of refreshing and unwrinkling may vary depending on the type of fabric, size of
or Steam Refresh .
the load and programme selected.
The
symbol appears in the display.
– After unwrinkling or refreshing, all fabrics must be removed immediately and hung crease-
free on a hanger or a washing line for 15 minutes.
Programmes
2. Remove the condensation tank completely.
Please observe the treatment symbols and manufacturer's instructions on the fabrics.
Do not use Short spin/Refresh for fabrics made of wool, leather, containing metal or
Before every Steam Dry - Steam Refresh cycle, fill the water tank with
wooden parts as well as wax and oil jackets!
distilled water only. Do not use tap water, condensation or additives.
Do not use any dryer cleaning sets!
Steam Dry
3. Fill the water tank. Use the jug supplied.
Minimum Iron Shirt
Suitable for easy-care fabrics, e.g. formal shirts. Fabrics are smoothed. You can expect
optimum results if "non-iron" appears on the care label. After the programme has finished,
If the water tank filter is dirty
the items must be removed immediately and hung crease-free on a hanger or washing line
See page 4.
for 15 minutes. The programme is for up to 5 formal shirts.
Minimum Iron Daily Load
Suitable for hard-wearing cotton fabrics, e.g. bed linen, tablecloths or formal shirts. Fabrics
are smoothed. You can expect optimum results if "non-iron" appears on the care label. After
4. Pour the distilled water into the filling hole on the water tank,
the programme has finished, the items must be removed immediately and hung crease-free
until the
symbol goes out on the display panel.
on a hanger or washing line for 15 minutes. The programme is for up to 5 formal shirts or
1 to 2 larger items.
If drying the recommended load, approximately 250 to 300 ml of distilled
water is used in the Steam Dry - Steam Refresh programmes.
Steam Refresh
5. Insert the condensation container all the way.
Business
Suitable for refreshing suits, jackets and trousers, or dry-clean items that cannot be washed
in the washing machine
see the care label. The programme only refreshes fabrics and
does not clean them. After the end of the programme, the items must be removed
immediately. Programme for 1 suit or 1 to 2 smaller items.
Freshen up
6. Start the Steam Dry or Steam Refresh programme.
Suitable for refreshing casual wear made of cotton or artificial fibres. Fabrics must be
suitable for dryers
see the care label. The programme refreshes fabrics only, and does
not clean them. After the programme has finished, the fabrics must be removed
immediately. Programme for 1 pullover, 2 pairs of trousers or formal shirts.
8
Installation
– Scope of delivery: dryer, installation and instruction manual, jug, basket for woollens
Cleaning is therefore not required
(depending on the model).
– Check dryer for transport damage.
– The dryer is heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– Do not install in a room where there is a risk of freezing. Freezing water may cause damage.
– If in doubt, have the appliance connected by a specialist.
– Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
Setting up the dryer
Remove all accessories
1.
– The appliance plug must always be accessible.
from the drum.
The drum must be empty.
– Ensure that the appliance is installed on a clean, level
and firm surface.
– Keep the cooling grille on the front of the dryer
clear.
– Keep the area around the dryer clean.
– Level the dryer using the threaded feet.
Use a spirit level.
– Do not remove the threaded feet under any
circumstances.
Do not install the dryer behind a door or sliding
door, which could prevent or restrict opening of the
dryer door. This will prevent children from locking
clean the filter in the water tank.
themselves in and putting their lives in danger.
2.
Mains connection
see safety information
Page 13.
– Connect to an AC earthed socket. If in doubt, have the socket checked by a specialist.
– The mains voltage and the voltage shown on the rating plate (
Page 11) must be the same.
– The connected load and necessary fuse protection are specified on the rating plate.
Do not operate the dryer if there
Frost protection / Transport
is a danger of frost.
Preparation
1. Empty the condensation container
Page 4.
2. Select any programme using the programme selector.
3. Press the
Start/Stop button
condensation is pumped into the container.
4. Wait 5 min., and then empty the condensation container again.
5. Turn the programme selector to Off.
The water tank must not contain any distilled water. If necessary, run the Steam/Refresh programme.
9
Technical data
What to do if...
Dimensions (DxWxH)
60 x 60 x 85 cm (adjustable height)
Weight
approximately 43.5 kg
Max. capacity
8 kg
Condensation container
4.0 l
Water tank
approx. 0.4 l
Connection voltage
220-240 V
Connected load
max. 2800 W
Fuse protection
13 A
Ambient temperature
5 - 35 °C
Product number
Inside of door
Production number
The rating plate can be found on the back of the dryer.
Consumption rates
These are guide values determined under standard
conditions.
Spin speed in rpm
Drying time
Energy
(residual moisture)
in min.**
consumption
in kWh**
Cottons 8 kg
Cupboard Dry*
1400
(approx. 50 %)
105
3.74
1000
(approx. 60 %)
122
4.49
800
(approx. 70 %)
139
5.17
Iron Dry*
1400
(approx. 50 %)
83
2.24
Clean and level
Make sure that the air inlet
1000
(approx. 60 %)
100
3.44
remains unobstructed
800
(approx. 70 %)
117
3.86
Easy-Care 3.5 kg
1000
39
1.05
Cupboard Dry*
800
(approx. 40 %)
42
1.35
600
(approx. 50 %)
51
1.65
*Test programme to DIN EN 61121
**The values may differ from those given, depending on overvoltage and undervoltage, the
type of fabric, composition of the laundry to be dried, the residual moisture in the fabric and
the size of the load.
Drum interior light (bulb E14, 25 W)
The drum is illuminated after the door is opened or closed, and after the programme has
started. The light goes out automatically. To change the bulb
Page 12.
Optional accessories
(order from the after-sales service using the order number)
Connecting kit for condensation outlet
WTZ
1110
The condensation is drained off immediately via a hose.
Washer-dryer stack connection set
WTZ
The dryer can be stacked on top of a suitable washing machine of the same depth and width,
11310
to save space. The dryer must be secured to the washing machine with this connection set.
With pull-out worktop: WTZ 11300
Installation underneath the worktop
WTZ
Instead of the appliance covering plate, you must have a metal cover fitted by a specialist.
10290
10
11
Safety instructions
If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales
Emergency
– Pull the appliance plug out of the socket immediately or disconnect the fuse.
service. We will always find an appropriate solution and will avoid unnecessary visits by
ONLY use the
– in rooms inside the house.
engineers. Trust the expertise of the manufacturer and rest assured that the repair will be
dryer...
– for drying or unwrinkling/refreshing fabrics.
carried out by trained service technicians using original spare parts. The contact details of your
local after-sales service can be found in the enclosed after-sales service directory, or by
The dryer must
– be used for purposes other than those described above.
calling one of these numbers:
NEVER...
– be modified in terms of its technology or properties.
– GB 0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute.
Hazards
– The dryer must not be used by children or persons who have not been
A call set-up fee of up to 6 pence may apply.)
instructed in its use.
– IE 01450 2655
– Do not leave children unsupervised near the dryer.
When contacting the after-sales service, please quote the appliance's product number (E no.)
– Keep pets away from the dryer.
and production number (FD) (see the inside of the door).
Set the programme selector to Off and remove the appliance plug from the socket.
– Remove all objects from pockets,
and lighters in particular
The
Start/Stop indicator light
Mains plug plugged in?
does not come on.
Programme selected?
– Do not lean or sit on the door
– Open the door carefully. Hot steam may escape. The clothes and drum may
The
symbol and
Start/Stop
Empty the condensation container
Page 4.
indicator light are flashing.
Check the condensation outlet hose, if applicable (kink).
be hot
risk of burns.
The
symbol and
Start/Stop
Clean the air cooler
Page 6 "Cleaning and care". Clean the
Installation
– Secure loose leads or hoses, otherwise there is a risk of tripping.
indicator light are flashing.
fluff filter
Page 4.
– Below 0 °C there is a possibility of frost damage.
The
symbol flashes.
Is the water tank empty?
Mains
– Connect the dryer according to specifications to an AC earthed socket,
Filling with distilled water
Page 9.
connection
The Steam Dry - Steam Refresh
The filter in the water tank may have become dirty.
otherwise it cannot be guaranteed that the appliance is completely safe.
does not start.
If so, clean the filter in the water tank
Page 4.
– The cable cross-section must be sufficient.
Dryer does not start.
Has the
Start/Stop button been pressed? Is the door closed?
– Only use earth-leakage circuit breakers with the following symbol:
Programme set?
– The appliance plug and socket must be compatible.
Ambient temperature greater than 5 °C?
– Do not use multiple plugs/connectors and/or extension cables.
Water is leaking out.
Make sure the dryer is level.
Clean the air cooler seal.
– Do not touch or hold the appliance plug with wet hands
The door opens by itself.
Push the door closed until you hear it click into place.
risk of electric shock.
– Never pull the appliance plug out of the socket by its cable.
Items crease even though the
Laundry load exceeded?
– Do not damage the mains lead
Steam Dry - Steam Refresh
Remove articles of clothing immediately after the end of the
programme has been selected.
programme, hang up and pull into shape.
Operation
– Only laundry must be loaded into the drum.
Creasing.
Laundry load exceeded?
Before switching on the dryer - check the contents.
Remove articles of clothing immediately after the end of the
– Do not use the dryer if the laundry has been in contact with solvents, oil, wax,
programme, hang up and pull into shape.
grease or paint (e.g. hair setting spray, nail polish remover, stain remover,
Unsuitable programme selected
Page 7.
cleaning solvent, etc.)
Drying result is not satisfactory
Warm laundry feels damper than it actually is.
– Hazard caused by dust (e.g. coal dust, flour): do not use the dryer
(laundry feels too damp).
The selected programme does not suit the load. Use another
risk of explosion.
drying programme or, in addition, select the time programme
– Do not put laundry containing foamed material/rubber in the dryer
Page 7.
material may be destroyed and the dryer may be damaged due to possible
Use fine adjustment for the drying result
Page 1/2.
Fine layer of limescale on the humidity sensors
deformation of the foamed material.
Clean the humidity sensors
Page 6.
– Switch off the dryer once the programme has ended.
Programme termination, e.g. tank full, mains power supply
– For unwrinkling/refreshing fabrics, use distilled water only. Do not use
failure, door open or maximum drying time reached.
condensation, tap water or additives.
Drying time too long.
Rinse the fluff filters under running water
Page 4.
– Distilled/condensation water is not for drinking.
Insufficient supply of air
ensure that air can circulate.
Air inlet possibly blocked
Clear inlet
Page 10.
Defect
– Do not use the dryer if it is defective or if you suspect that it is.
Ambient temperature higher than 35 °C
ventilate the room.
Repairs must only be carried out by the after-sales service.
The humidity in the room increases
Make sure the room is sufficiently ventilated.
– Do not use a dryer with a faulty mains lead. To prevent risks, a faulty mains
significantly.
lead must only be replaced by the after-sales service.
One or more programme status
Clean the filter and air cooler under running water
Page 4/6.
– Before changing the bulb of the interior light make absolutely sure you have
indicator lamps are flashing.
Check the installation conditions
Page 10.
pulled the appliance plug from the socket
Switch off, allow to cool, switch on again and restart the
programme.
Spare parts
– Only use genuine spare parts and accessories for safety reasons.
The interior light (depending on the
Unplug the appliance plug, fold back the cover cap on the inside
Disposal
– Dryer: unplug the appliance plug, then cut the mains lead from the appliance.
model) does not work.
above the door (using a Torx 20 screwdriver)
Dispose of the dryer at an approved public disposal facility.
and replace the bulb. Close the cover cap.
– Packaging: keep all packaging out of reach of babies and children.
danger of suffocation.
– All materials are environmentally safe and recyclable. Dispose of in an
environmentally-responsible manner.
12
risk of explosion.
risk of tipping.
risk of electric shock.
fire/explosion hazard.
elastic
Dryer
en Instruction manual
risk of electric shock.
13
Hide quick links:
Advertisement
Table of Contents
