Advantech TPC-651T-E Series User Manual

Advantech TPC-651T-E Series User Manual

Industrial touch panel computers with intel® atom™ processors
Hide thumbs Also See for TPC-651T-E Series:

Advertisement

Quick Links

User Manual
TPC-651T-Exxx
TPC-651H-Exxx
Industrial Touch Panel Computers with
®
Intel
Atom™ Processors

Advertisement

Table of Contents
loading

Summary of Contents for Advantech TPC-651T-E Series

  • Page 1 User Manual TPC-651T-Exxx TPC-651H-Exxx Industrial Touch Panel Computers with ® Intel Atom™ Processors...
  • Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
  • Page 3 Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
  • Page 4 This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information.
  • Page 5 The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
  • Page 6 Caution! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dis- pose of used batteries according to the manufacturer's instructions. Attention! Danger d'explosion si la pile est remplacée de façon incor- recte.
  • Page 7: Table Of Contents

    Chapter General Information ......1 Introduction ....................2 Specifications .................... 2 1.2.1 System Kernel................2 1.2.2 I/O Ports..................2 1.2.3 O/S support................... 2 1.2.4 Safety and Environment..............3 LCD Specifications..................3 Touchscreen Specifications ..............4 Power ......................4 I/O Ports Arrangement ................4 Figure 1.1 I/O Port Arrangement ..........
  • Page 8 EC Watchdog Timer Driver Installation........... 34 Intel Graphics Driver Installation ............. 38 Intel Chipset Software Installation Utility Installation....... 41 Intel® Trusted Execution Engine Driver Installation........ 43 LAN Driver Installation ................46 Windows 7 USB 3.0 Driver Installation ........... 49 Touchscreen Driver Installation .............. 51 B.10 Touchscreen Calibration .................
  • Page 9: Chapter 1 General Information

    Chapter General Information...
  • Page 10: Introduction

    Introduction The TPC-651T/TPC-651H Touch Panel Computer is a state-of-the-art Human Machine Interface featuring a 5.7”/6.5” display and Intel Atom™ E3827 1.75 GHz Processor The key features are as follows:  True-flat touch screen TPC-651T is a true-flat touch screen designed with IP66 front protection. (TPC- 651H is with traditional TPC bezel for IP65 front protection) ...
  • Page 11: Safety And Environment

    1.2.4 Safety and Environment Safety FCC Class A   CE certificated  The front bezel is compliant with IP66 for true flat models and IP65 for the TPCs with the traditional front bezel Environment  Operating Temperature: – -20 ~ 60°C (-4 ~ 140°F) Storage Temperature: ...
  • Page 12: Touchscreen Specifications

    Touchscreen Specifications  Touch Type: 5- wire Resistive  Base Glass Construction: Tempered glass  Resolution: 640 x 480 (following resolution of system)  Light Transmission: 80% ± 3% (Measured by BYK-Gardner)  Controller: USB Interface  Lifespan: 1 million touches at single point Note! Touchscreen ITO maybe crash duo to heavy usage .
  • Page 13: Panel Mounting

    Panel Mounting There is a rubber waterproof gasket on the AL front bezel. Make sure the water- proof gasket is in position before installing TPC into the panel opening. Install the TPC into the panel opening. Take the clamps and long screws from the accessory box. Hook the clamps to the holes around the four sides of the bezel.
  • Page 14 Figure 1.2 TPC-651T Dimensions TPC-651T/TPC-651H User Manual...
  • Page 15 Figure 1.3 TPC-651H Dimensions TPC-651T/TPC-651H User Manual...
  • Page 16 TPC-651T/TPC-651H User Manual...
  • Page 17: Chapter 2 System Setup

    Chapter System Setup...
  • Page 18: System Setup

    System Setup You can easily get TPC started by following the below steps. Unpack the TPC package. Check the packing list at the beginning of this manual to make sure all items have been included. Figure 2.1 Unpack the Package TPC-651T/TPC-651H User Manual...
  • Page 19 ® Install a CFast card containing the operating system. Figure 2.2 Install CFast Memory Card (Mylar in accessory box can be attached to CFast card for easy extraction) Warning! It is suggested to turn OFF system power as you plug in or pull out the memory card, even though the CompactFlash memory is hot swappa- ble.
  • Page 20: Installing The Drivers

    Note! The drivers and utilities used for the TPC-651T panel PCs are subject to change without notice. If in doubt, check Advantech's website or contact our application engineers for the latest information regarding drivers and utilities.
  • Page 21: Transport And Unpacking

    Transport and Unpacking When accepting a delivery, please check the packaging for visible transport damage and check the delivery for completeness by comparing it with your order. If you notice any shipping damage or inconsistencies between the contents and your order, please inform the responsible delivery service immediately.
  • Page 22 Secure the clamp to the panel using the included screws Smaller screws are included with the TPC-651T/TPC-651H, use these to avoid blocking CFast slot or I/O ports. Use Hex Wrench No.2 to secure clamp Hex screw 1930005092 Clamp 1930005092 TPC-651T/TPC-651H User Manual...
  • Page 23: Cabinet Installation And Earth Grounding Setup

    Cabinet Installation and Earth Grounding setup Please follow the following steps to setup TPC-651T/TPC-651H, and please pay attention that Ground pin of TPC-651T should be connected to earth ground. Under this circumstance, TPC-651T could have the best performance such as EMI immu- nity, ESD immunity, Surge immunity and also system isolation.
  • Page 24 System wiring Step A: Connect the cabinet to earth ground. Step B: Ensure that all cabinet has been grounded together. Step C: Connect the ground of the power supply to the cabinet. Step D: Connect the ground pin of TPC-651T/TPC-651H to the cabinet. Step E: Connect the I/O to the controller if needed.
  • Page 25: Power/Digital Ground And Earth Ground

    Power/Digital Ground and Earth Ground The purpose is to block all the external interference on the chassis, and prevent any possibility of bad grounding design to cause electric shock of people. This is so called level 1 isolation which consumer PC do not implement this kind of design. ...
  • Page 26 TPC-651T/TPC-651H User Manual...
  • Page 27: Appendix A Serial Port Settings

    Appendix Serial Port Settings...
  • Page 28: Jumper, Dip Switch And Connector Location

    Jumper, Dip switch and Connector location A.1.1 A.1.2 Bottom TPC-651T/TPC-651H User Manual...
  • Page 29: Switch Setting

    Switch Setting COM2 RS232/422/485 mode setting (SW2) COM2 RS232/422/485 mode setting Description This switch is used to select COM2 RS232/422/485 mode setting Default RS232 mode Bit 1,2,3,4,5 ON RS232 Mode Bit 6,7,8,9,10 OFF Bit 1,2,3,4,5,10 OFF RS422 Master Mode Bit 6,7,8,9 ON Bit 1,2,3,4,5 OFF RS422 Slave Mode Bit 6,7,8,9,10 ON...
  • Page 30: Termination Resistor Select (Sw3)

    A.2.1 Termination Resistor Select (SW3) Termination Resistor Select This switch is used to select Termination Resistor (120 ohm) for long Description distance transmission or device matching. Default Bit1 & Bit2 (ISO_COM2_DATA+ & ISO_COM2_RX-) ISO_COM2_DATA+ Pin 1 ISO_COM2_RX- Pin 2 Default ISO_COM2_R_RX+ Pin 3 ISO_COM2_R_DATA- Pin 4...
  • Page 31: Mini Pcie Slot (Minipcie)

    A.3.3 Mini PCIE slot (MINIPCIE) 1654002538 MINI PCI E 52P 6.8mm 90D SMD AS0B226-S68N7H Supports PCI1.1, PCI1.2 Power Definition Signal Description Signal Description +3.3Vaux / PCI1.1 was +3.3V, PCI1.2 was +3.3Vaux 51 Reserved +3.3V Reserved +1.5V Reserved Reserved The pin to select the Pin 2, 52 power PIN43_MPCIE_ output for +3.3Vaux or +3.3V (PCI1.1 PWRSEL...
  • Page 32: Cfast Slot (Cn14)

    A.3.4 CFast slot (CN14) 1653004849 CFast 24P 1.27mm 90D(M) SMD N7G24-A0B2RA-10-0HT- The host is connected to the CFast Card using a 7+17 pin connector Segment CFast Name Description SATA SGND Ground for signal integrity SATA Signal Pair A : TX+/- (Transmit) SATA SATA...
  • Page 33: Lan Rj45 Connector (Cn7,Cn8)

    A.3.6 LAN RJ45 connector (CN7,CN8) 1652002996 PHONE JACK RJ45 14P 90D(M) DIP RTA-195AAK1A RJ45 Pin Signal Description  In BASE-T: Media Dependent Interface[0]:  1000BASE-T: In MDI configuration, MDI[0]+/- corre- MDI0+ sponds to BI_DA+/- and in MDI-X configuration MDI[0]+/- corresponds to BI_DB+/-. ...
  • Page 34: Usb Connector (Cn10)

    A.3.7 USB connector (CN10) 1654010199 USB Conn. 2.0+3.0 13P 90D(F) DIP UEA1112C-UHS6-4 Signal Description 1, 10 USB VBUS USB Power output ,USB2.0 5V/0.5A and USB3.0 5V/0.9A 2, 11 USB_P- USB2.0 date - 3, 12 USB_P+ USB2.0 date + 4,13 Ground for Power return SSRX- USB3.0 RX - SSRX+...
  • Page 35: Com2 Rs232/422/485 Connector (Cn16)

    A.3.9 COM2 RS232/422/485 connector (CN16) 1654000056 D-SUB Conn. 9P 90D(M) DIP 070241MR009S200ZU RS232 RS422 RS485 TPC-651T/TPC-651H User Manual...
  • Page 36 TPC-651T/TPC-651H User Manual...
  • Page 37: Driver Installation And Configuration

    Appendix Driver Installation and Configuration...
  • Page 38: Ec Driver Installation

    EC Driver Installation Follow the steps below to install the EC drivers: Launch folder  \EC\Vx.xx.xxxx Install AdvEC_Vx.xx.xxxx.exe Click Next TPC-651T/TPC-651H User Manual...
  • Page 39 Click Install Click Finish Choose Yes, then click OK to restart TPC-651T/TPC-651H User Manual...
  • Page 40: Ec Brightness Control Tool Installation

    EC Brightness Control Tool Installation Note! The EC driver must be installed first Follow the steps below to install the EC brightness control tool: Launch folder \EC Brightness\Vx.xx.xxxx Install AdvECBrightness_Vx.xx.xxxx.exe Click Next TPC-651T/TPC-651H User Manual...
  • Page 41 Click Install Click Finish Choose Yes, then click OK to restart TPC-651T/TPC-651H User Manual...
  • Page 42: Ec Watchdog Timer Driver Installation

    EC Watchdog Timer Driver Installation Note! The EC driver must be installed first Follow the steps below to install the EC Watchdog Timer driver: Launch folder \WDT\Vx.xx.xxxx Install AdvWDT_Vx.xx.xxxx.exe TPC-651T/TPC-651H User Manual...
  • Page 43 Click Next Choose Advantech [EC]WDT, then click Next TPC-651T/TPC-651H User Manual...
  • Page 44 Click Install Click Finish TPC-651T/TPC-651H User Manual...
  • Page 45 Choose Yes, then click OK to restart TPC-651T/TPC-651H User Manual...
  • Page 46: Intel Graphics Driver Installation

    Intel Graphics Driver Installation Follow the steps below to install the Intel Graphics driver: Launch folder \Graphics Driver\Intel EMGD win7 32 bit\ Install Setp.exe Click Next TPC-651T/TPC-651H User Manual...
  • Page 47 Click Yes Click Next Click Install TPC-651T/TPC-651H User Manual...
  • Page 48 Click Next Choose Yes, then click Finish to restart TPC-651T/TPC-651H User Manual...
  • Page 49: Intel Chipset Software Installation Utility Installation

    Intel Chipset Software Installation Utility Installation Follow the steps below to install the Intel Chipset Software Installation Utility: Launch \Intel Chipset Software Installation Utility\SetupChipset_10.0.13_PV Install SetupChipset.exe Click Next TPC-651T/TPC-651H User Manual...
  • Page 50 Click Accept Click Install Click Finish TPC-651T/TPC-651H User Manual...
  • Page 51: Intel® Trusted Execution Engine Driver Installation

    ® Intel Trusted Execution Engine Driver Installation Follow the steps below to install the Intel Trusted Execution Engine driver: Launch folder \TXE\Intel TXE Firmware\Win7 Install kmdf-1.11-Win-6.1-x86.msu Click Yes TPC-651T/TPC-651H User Manual...
  • Page 52 Click Restart Now, then the system will restart Launch folder \\TXE\TXE_Win7_8_8.1_1.1.0.1089 Install SetupTXE.exe TPC-651T/TPC-651H User Manual...
  • Page 53 Click Next Click Next Click Next TPC-651T/TPC-651H User Manual...
  • Page 54: Lan Driver Installation

    Choose Yes, then click Finish to restart. LAN Driver Installation Follow the steps below to install the LAN driver: Launch folder \LAN\Win7 \Install_Win7_7077_11282013 Install setup.exe TPC-651T/TPC-651H User Manual...
  • Page 55 Click Next Click Install TPC-651T/TPC-651H User Manual...
  • Page 56 Click Finish TPC-651T/TPC-651H User Manual...
  • Page 57: Windows 7 Usb 3.0 Driver Installation

    Windows 7 USB 3.0 Driver Installation Follow the steps below to install the Windows 7 USB 3.0 driver: Launch folder \USB3\Win7\SetupUSB3_3.0.0.33 Install Setup.exe Click Next TPC-651T/TPC-651H User Manual...
  • Page 58 Click Yes Click Next Click Next TPC-651T/TPC-651H User Manual...
  • Page 59: Touchscreen Driver Installation

    Choose Yes, then click Finish to restart Touchscreen Driver Installation Follow the steps below to install the touchscreen driver: Launch folder \TS\PenMount Windows Universal Driver Vx.xx.xxxx(WHQL) Install Setup.exe TPC-651T/TPC-651H User Manual...
  • Page 60 Click Next Click I Agree Click Install TPC-651T/TPC-651H User Manual...
  • Page 61 Click Finish Click Finish TPC-651T/TPC-651H User Manual...
  • Page 62: Touchscreen Calibration

    B.10 Touchscreen Calibration Follow the steps below to install the touchscreen driver: Launch PenMount Control Panel tool Double click PenMount 6000 USB TPC-651T/TPC-651H User Manual...
  • Page 63 Follow the process to calibration touch screen Click OK to finish calibration TPC-651T/TPC-651H User Manual...
  • Page 64: Lmsensor Driver Installation

    B.11 LMsensor Driver Installation Follow the steps below to install the LMsensor driver: 1. Launch folder \Lmsensor\Vx.xx.xxxx 2. Install Lmsensor_EC_Vx.xx.xxxx.exe 3. Next 4. Restart TPC-651T/TPC-651H User Manual...
  • Page 65: Appendix C Windows 8.X Bios Setup

    Appendix Windows 8.X BIOS Setup...
  • Page 66: Windows 8.X Bios Setup

    Windows 8.X BIOS Setup Entre BIOS setting menu then go to Advanced page for Miscellaneous Configuration Select OS Selection to Widows 8.X  TPC-651T/TPC-651H User Manual...
  • Page 67 TPC-651T/TPC-651H User Manual...
  • Page 68 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2014...

This manual is also suitable for:

Tpc-651h-e series

Table of Contents