1. Manuals
  2. Brands
  3. Fohrenbach Manuals
  4. Crimp tool
  5. HT119
  6. User manual

Fohrenbach HT119 User Manual

Handpistol to crimp male pin terminals
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HT119
Handpistol to crimp
male pin terminals
User's Guide
www.foehrenbach.be

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HT119 and is the answer not in the manual?

Questions and answers

Related Manuals for Fohrenbach HT119

Summary of Contents for Fohrenbach HT119

  • Page 1 HT119 Handpistol to crimp male pin terminals User’s Guide www.foehrenbach.be...

  • Page 2: Table Of Contents

    5.1. Crimp Height Adjustment ....................12 6. PARTS ..........................13 6.1. Spare Parts ........................13 6.2. Parts Ordering Information ................... 13 6.3. Hand Tool Repair Policy....................13 Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev. : 4 Page : 2 /...

  • Page 3: Introduction

    The crimp is formed between the wire and insulation barrel anvils and the wire and insulation crimpers. Once closed, the ratchet releases and allows a spring to pull the lever open Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev.

  • Page 4: Specifications

    HT-0119 check with your distributor to be sure that the new terminal number is compatible with your hand tool. Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev.

  • Page 5: Operation

    (3 & 4). Then close the hand tool lever completely. This will crimp the terminal to the wire(s). Figure 2. Positioning Terminal for Crimping Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev. : 4 Page : 5 /...

  • Page 6: Terminal Inspection

    Make the following visual checks (see Figure 4). NOTE If inspection of the crimped terminal reveals any defects, the terminal has not been properly crimped and should be discarded. Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev. : 4...
  • Page 7 5. If the crimp heights do not meet the specifications listed in Section 1, Paragraph 2.4, refer to Section 5 for proper adjustment procedures. Figure 5. Measuring Crimp Height of Terminal Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev. : 4...

  • Page 8: Troubleshooting

    Insulation bulges around Wire or insulation diameter is Refer to section I, paragraph insulation barrel incorrect terminal D (specifications) for correct being used. insulation diameter requirements. Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev. : 4 Page : 8 /...

  • Page 9: Parts Replacement Procedures

    2. Loosen the two setscrews in the anvil holder and remove the terminal holder (see Figure 7). 3. Remove the cap screw and defective anvil(s) from the anvil holder (see Figure 8). Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev.
  • Page 10 Then tighten the anvil holder set screws. 6. Crimp a terminal to the proper size wire. Then inspect the terminal as described in section II, paragraph B. Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev. : 4...

  • Page 11: Wire And Insulation Barrel Crimpers And Tonker Replacement (See Figure 13)

    13. Crimp a terminal to a proper-size wire and inspect the terminal as described in Section II, paragraph B. Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev. : 4...

  • Page 12: Adjustment Procedures

    Next, insert a pin approximately 1/16-inch in diameter, into one of the holes in the collar (see Figure 12). Then rotate the collar about 5 degrees counterclockwise to increase crimp height or clockwise to decrease crimp height. Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev.

  • Page 13: Parts

    Föhrenbach Application Tooling charges a standard rate to repair any hand tool not under warranty. Föhrenbach Application Tooling will repair the hand tool and return it to you by the fastest means possible. Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev.
  • Page 14 GUIDE PIN 144547-001 GUIDE RAIL 147071-1 TERMINAL CLAMP 147072-1 QUILL PUNCH 102470-2 PUNCH SPRING, 0.300. LONG 150564-1 COLLAR. NYLON_, PRESS-FIT, 0.0625. I.D. *Recommended Spare Parts Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev. : 4 Page : 14 /...
  • Page 15 The technical data in this publication has been carefully checked and assembled. No liability from inaccuracies or errors is assumed. The right to change or improve this document without notice is reserved. Instruction manual HT119 www.foehrenbach.be Date : August 2007 Documentrev.

Table of Contents