Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fohrenbach HT95
Summary of Contents for Fohrenbach HT95
- Page 1 HT95 Handpistol mini PV AWG 22-32 User’s Guide...
-
Page 2: Table Of Contents
4.3 Holding pin replacement ..................11 5. Crimp height adjustment ..................12 6. Parts........................14 6.1 Spare parts......................14 6.2 Parts ordering information..................14 6.3 Hand tool repair policy ..................14 Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. : 3 Page : 2 / 15... -
Page 3: Introduction
The crimp is formed between the wire and insulation barrel anvils and the wire and insulation crimpers. Once closed, the ratchet releases and allows a spring to pull the lever open. Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. -
Page 4: Specifications
HT95, check with your distributor or Föhrenbach Application Tooling NV to be sure that the new terminal number is compatible with your hand tool. -
Page 5: Operation
(see figure 3), then close the hand tool lever completely. This will crimp the terminal to the wire(s). Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. -
Page 6: Terminal Inspection
Check that all wire strands were crimped within the wire barrel. Check that the end of the wire insulation lies between the insulation and wire barrel. Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. - Page 7 Next, obtain a crimp height micrometer and measure the areas of the terminal shown in figure 5. If the crimp heights do not meet the specifications listed in Section I, paragraph D, refer to Section V for proper adjustment procedures. Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev.
-
Page 8: Troubleshooting
Wire size or insulation Refer to Section 1, paragraph insulation barrel. diameter is incorrect for 4 (specifications) for correct the terminal being used. insulation diameter requirements. Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. : 3 Page : 8 / 15... -
Page 9: Parts Replacement Procedure
3. Re-install terminal holder (10) to the anvil holder (4) and tighten the two 2-56 setscrews (12). 4. Crimp a terminal to a proper-sized wire, and inspect the terminal as described in Section II, paragraph B. Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. : 3... -
Page 10: Wire And Insulation Barrel Crimpers And Tonker Replacement
5. Place spring retainer (21) over tonker springs (19). Make sure springs are fully compressed, then loosely attach the spring retainer (21) and the crimper holder (1) to the hand tool with a 6-40 cap screw (13). Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. -
Page 11: Holding Pin Replacement
(10) until pins are flush with the extended supports. Be sure that a flat side of each pin is at right angles to the two 2-56 setscrew holes on top of the terminal holder (10). Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. -
Page 12: Crimp Height Adjustment
(4), then lock the adjusting collar by tightening the setscrew in the adjustable tool holder (11). Reinstall terminal holder assembly and anvil holder as described in steps 5 through 7 above. Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. - Page 13 Guide pin "O" ring, 01-004 102470-1 Holding spring 104964-1 Tanker A-1153 Spring tanker A-11 55 Spring guide 104963-1 Spring retainer * Recommended Spare Parts Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. : 3 Page : 13 / 15...
-
Page 14: Parts
Belgium. Provide the description of the part, part number (if specified), quantity desired, and also the hand tool model and serial number. 6.3. Hand Tool Repair Policy The repair cost is according to expenses. Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev. : 3... - Page 15 The technical data in this publication has been carefully checked and assembled. No liability from inaccuracies or errors is assumed. The right to change or improve this document without notice is reserved. Instruction manual HT95 www.foehrenbach.be Date : August 2007 Documentrev.
Need help?
Do you have a question about the HT95 and is the answer not in the manual?
Questions and answers