Table of Contents
Advertisement
W4E315-CS22-75
3.2 Nominal data
Motor
M4E068-DF
Phase
1~
Nominal voltage / VAC
115
Frequency / Hz
60
Method of obtaining
ml
data
Valid for approval/
-
standard
-1
Speed (rpm) / min
1510
Power consumption / W
150
Current draw / A
1.31
Capacitor / µF
14
Capacitor voltage / VDB
250
Capacitor standard
S2 (CE)
Max. back pressure / Pa
80
Min. ambient
-25
temperature / °C
Max. ambient
70
temperature / °C
Starting current / A
2.8
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
4.36 kg
Size
315 mm
Motor size
68
Rotor surface
Painted black
Blade material
Press-fitted sheet steel blank, sprayed
with PP plastic
Fan housing material
Sheet steel, galvanized and coated with
black plastic (RAL 9005)
Guard grille material
Steel, coated with black plastic (RAL
9005)
Number of blades
5
Airflow direction
V
Direction of rotation
Counterclockwise, viewed toward rotor
Degree of protection
IP44; installation- and position-dependent
as per EN 60034-5
Insulation class
"F"
Moisture (F) /
H1
Environmental (H)
protection class
Installation position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
On rotor side
drainage holes
Mode
S1
Motor bearing
Ball bearing
Touch current
< 0.75 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Motor protection
Thermal overload protector (TOP)
internally connected
Item no. 16658-5-9970 · ENU · Change 226753 · Approved 2021-02-24 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
with cable
Protection class
Motor capacitor
1~
according to EN 60252-
115
1 in safety protection
60
class
Conformity with
ml
standards
Comment on CE
UL 1004-3
Approval
1510
160
1.34
14
250
UL
; Use the device in accordance with its degree of protection.
80
Information on surface quality
-25
The surfaces of the products conform to the generally applicable industrial
70
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
2.9
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
3.4 Mounting data
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Strength class of
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
3.5 Transport and storage conditions
Max. permitted
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)
Axial
I (with customer connection of protective
earth)
S0
EN 60034-1; EN 60204-1; EN 60335-1
Commissioning not permitted in the
European Economic Area
UL 1004-3; CSA C22.2 No. 77
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
8.8
locking screws).
+80 °C
-40 °C
Advertisement
Table of Contents
