DeWalt DCD980 Instruction Manual
Hide thumbs
Also See for DCD980:
- Instruction manual (57 pages) ,
- Original instructions manual (157 pages) ,
- User manual (14 pages)
Table of Contents
Advertisement
Quick Links
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
Fig. A
4
8
Trigger switch
1
Forward/reverse control button
2
Worklight
3
Chuck
4
Torque adjustment collar
5
Mode control collar
6
Gear shifter
7
Side handle
8
Battery pack
9
Battery release button
10
Belt hook (optional accessory
11
Bit clip (optional accessory)
12
Screw
13
5
6
3
2
1
10
9
if you have any questions or comments about this or
any D
1-800-4-D
7
11
12
13
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING: To reduce the risk of injury, read the
instruction manual.
WALT tool, call us toll free at:
e
WALT (1-800-433-9258).
e
English
13
1
Advertisement
Table of Contents
Related Manuals for DeWalt DCD980
Summary of Contents for DeWalt DCD980
- Page 1 English Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
-
Page 2: General Power Tool Safety Warnings
English GENERAL POWER TOOL SAFETY WARNINGS b ) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust WARNING! Read all safety warnings and all mask, non-skid safety shoes, hard hat, or hearing instructions. Failure to follow the warnings and protection used for appropriate conditions will reduce instructions may result in electric shock, fire and/or personal injuries. -
Page 3: Additional Safety Information
English into account the working conditions and the producing applications such as hammerdrilling and work to be performed. Use of the power tool for drilling metals. operations different from those intended could result • Do not operate this tool for long periods of time. in a hazardous situation. -
Page 4: Batteries And Chargers
English The label on your tool may include the following symbols. The buildings in summer). For best life store battery packs in symbols and their definitions are as follows: a cool, dry location. NOTE: Do not store the battery packs in a tool with V ...... - Page 5 120V Max* (two 60V Max* batteries) product, it will operate For more information regarding fuel gauge battery packs, as a 60V Max* battery. please contact call 1-800-4-D WALT (1-800-433-9258) or visit our website www.dewalt.com. shipping Mode: When the cap is attached to the The RBRC® Seal FLEXVOLT™ battery, the The RBRC®...
- Page 6 English • An extension cord must have adequate wire size CAUTION: Burn hazard. To reduce the risk of injury, (AWG or American Wire Gauge) for safety. The smaller charge only D WALT rechargeable battery packs. the gauge number of the wire, the greater the capacity Other types of batteries may overheat and burst of the cable, that is, 16 gauge has more capacity than 18 resulting in personal injury and property damage.
-
Page 7: Charger Operation
English • To comply with FCC and Industry Canada RF radiation DCB107, DCB112, DCB113, DCB115, DCB118, DCB132 exposure limits for general population, the antenna used Charging for this device must not be co-located or operating in conjunction with any other antenna or transmitter. Fully Charged For Bluetooth®... -
Page 8: Charger Cleaning Instructions
English screw exposed. Align the slots on the back of the charger nOTE: Battery packs should not be stored completely with the exposed screws and fully engage them in the slots. depleted of charge. The battery pack will need to be recharged before use. - Page 9 English Hammerdrilling (Fig. F) The center position of the control button locks the tool in the off position. When changing the position of the control CAUTION: When the mode collar is in the drill/ button, be sure the trigger is released. hammerdrill mode, the drill will not clutch out nOTE: The first time the tool is run after changing the regardless of the position of the torque adjustment...
-
Page 10: Installing And Removing The Battery Pack
English Your tool features a keyless chuck with one rotating sleeve The belt hook 11 and bit clip 12 can be be attached to for one-handed operation of the chuck. To insert a drill bit or either side of the tool using only the screw 13 ... -
Page 11: Maintenance
The torque adjustment collar may be set to any Tool Co., 701 East Joppa Road, Towson, MD 21286, call number at any time. However, the torque adjustment collar 1-800-4-D WALT (1-800-433-9258) or visit our website: is only engaged during screwdriving mode and not in drill www.dewalt.com. and hammerdrill modes. -
Page 12: Register Online
2–9/16" (65 mm) 2–9/16" (65 mm) after purchase. Hole saw 4" (100 mm) 4" (100 mm) 2 YEARs FREE sERViCE On DEWAlT BATTERY PACKs METAl DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120, Twist 1/2" (13 mm) 1/2" (13 mm) DCB127, DCB201, DCB203BT, DCB207, DCB361 Hole saw 1–3/8"...