Table of Contents
Advertisement
Available languages
Available languages
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
Tape measure
■
Flat-blade screwdriver
■
Phillips screwdriver
■
Level
■
Hand or electric drill
■
Wrench or pliers
■
Marker or pencil
■
Masking tape
■
Parts Supplied
Check that all parts are included.
10-32 hex nuts (attached to terminal block) (3)
■
Direct wire lugs (3)
■
#10 x 1
/
" (41 mm) screws (for mounting anti-tip bracket) (2)
5
■
8
Anti-tip bracket (inside oven cavity)
■
Anti-tip bracket must be securely mounted to the back wall
or floor. Thickness of flooring may require longer screws to
anchor bracket to subfloor. Longer screws are available from
your local hardware store.
For Model:
■
Oven racks
Parts Needed
If using a power supply cord kit:
A UL Listed power supply cord kit marked for use with
■
ranges. The cord should be rated at 250 volts minimum,
40 amps or 50 amps, that is marked for use with nominal
1
/
" (3.5 cm) diameter connection opening, and must end
3
8
in ring terminals or open-end spade terminals with upturned
ends.
A UL Listed strain relief.
■
Check local codes. Check existing electrical supply. See the
appropriate "Electrical Requirements" section.
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
INSTALLATION REQUIREMENTS
1/4" (6.4 mm) drive ratchet
■
1/4" (6.4 mm) nut driver
■
3/8" (9.5 mm) and 5/16"
■
(8 mm) nut driver
1/8" (3.2 mm) drill bit
■
(for wood floors)
Tin snips or large wire
■
cutters (for cutting ground
strap if necessary)
WEE750H0H
YWEE750H0H
WEEA25H0H
YWEEA25H0H
3
Optional Parts
To purchase these or any other accessories, please reference the
"Accessories" section of the User Guide for contact information.
Side Trim Kits:
■
White - Order Part Number W10675027
Black - Order Part Number W10675026
Stainless Steel - Order Part Number W10675028
Backsplash Kits:
■
High 6" (15.2 cm) White - Order Part Number W10655448
High 6" (15.2 cm) Black - Order Part Number W10655449
High 6" (15.2 cm) Stainless Steel - Order Part Number
W10655450
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
It is the installer's responsibility to comply with installation
■
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located behind the oven door on
the top right-hand side of the oven frame.
To eliminate the risk of burns or fire by reaching over the
■
heated surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage
is to be provided, the risk can be reduced by installing a
range hood or microwave hood combination that projects
horizontally a minimum of 5" (12.7 cm) beyond the bottom of
the cabinets.
The range should be located for convenient use in the
■
kitchen.
Recessed installations must provide complete enclosure of
■
the sides and rear of the range.
All openings in the wall or floor where range is to be installed
■
must be sealed.
Cabinet opening dimensions that are shown must be used.
■
Given dimensions are minimum clearances.
The anti-tip bracket must be installed. To install the anti-tip
■
bracket shipped with the range, see the "Install Anti-Tip
Bracket" section.
Grounded electrical supply is required. See the appropriate
■
"Electrical Requirements" section.
Contact a qualified floor covering installer to check that the
■
floor covering can withstand at least 200°F (93°C).
Use an insulated pad or 1/4" (6.4 mm) plywood under range
■
if installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with
your builder or cabinet supplier to make sure that the materials
used will not discolor, delaminate, or sustain other damage. This
oven has been designed in accordance with the requirements
of UL and CSA International and complies with the maximum
allowable wood cabinet temperatures of 194°F (90°C).
3
Advertisement
Table of Contents
