Dahua DH-IPC-D1BX0-B Quick Start Manual

Dahua DH-IPC-D1BX0-B Quick Start Manual

Ez-ip hd indoor wi-fi dome

Advertisement

Quick Links

EZ-IP HD Indoor Wi-Fi Dome
Network Camera
Quick Start Guide
V1.0.0

Advertisement

Table of Contents
loading

Summary of Contents for Dahua DH-IPC-D1BX0-B

  • Page 1 EZ-IP HD Indoor Wi-Fi Dome Network Camera Quick Start Guide V1.0.0...
  • Page 2: Foreword

    Foreword General This Quick Start Guide (hereinafter referred to be "the Guide") introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the Guide. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, WARNING could result in slight or moderate injury.
  • Page 3  All the designs and software are subject to change without prior written notice. The product updates might cause some differences between the actual product and the Guide. Please contact the customer service for the latest program and supplementary documentation. There still might be deviation in technical data, functions and operations description, or ...
  • Page 4: Important Safeguards And Warnings

    Important Safeguards and Warnings Electrical Safety  All installation and operation should conform to your local electrical safety codes.  The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited power Source requirement according to IEC60950-1.
  • Page 5  It is recommended to use the device together with lightning arrester to improve lightning protection effect.  It is recommended to ground the device to enhance reliability. Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with air ...
  • Page 6: Regulatory Information

    Regulatory Information The regulatory information herein might vary according to the model you purchased. Some information is only applicable for the country or region where the product is sold. FCC Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
  • Page 7: Table Of Contents

    Table of Contents Foreword ..............................I Important Safeguards and Warnings ....................III Regulatory Information ......................... V 1 Introduction ............................1 2 Network Configuration ........................2 Initializing Device ......................... 2 Modifying Device IP Address ....................... 3 Logging in Web Interface ......................4 3 Installation ............................
  • Page 8: Introduction

    Introduction Cable type might vary with different devices, and the actual product shall prevail.  Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit  and water damage. For the detailed operation, see the FAQ manual. Figure 1-1 Cable list For more information about cable ports, see Table 1-1, and for the pattern of the LED Indicator,...
  • Page 9: Network Configuration

    Network Configuration Device initialization and IP address setting can be finished with the "ConfigTool" or in web interface. For more information, see the WEB operation manual. Device initialization is available on select models, and it is required at first use or after the ...
  • Page 10: Modifying Device Ip Address

    The Device initialization interface is displayed. Step 6 Select the devices that need initialization, and then click Initialize. The password setting interface is displayed. See Figure 2-2. Figure 2-2 Password setting Step 7 Set and confirm the password of the devices, then enter a valid email address, and then click Next.
  • Page 11: Logging In Web Interface

    Figure 2-3 Modify IP Address Step 3 Select Static mode, and then enter start IP, subnet mask, and gateway. IP addresses of multiple devices will be set to the same if you select the Same IP  checkbox. If DHCP server is available in the network, devices will automatically obtain IP ...
  • Page 12 Operation with Remote Monitoring App You can download the remote monitoring app and add your camera to the app to perform remote monitor on your phone. Step 1 Download and install the "iDMSS Plus" app from App Store or the "gDMSS Plus" app from Google Play.
  • Page 13 Figure 2-6 Live preview...
  • Page 14: Installation

    Installation Packing List  The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool are contained in the disk or the QR code, and the  actual packing shall prevail. Dimension Following figures are for reference only, and the actual product shall prevail.
  • Page 15: Installing Device

    Installing Device 3.3.1 Installation Type...
  • Page 16: Detaching The Dome

    3.3.2 Detaching the Dome 3.3.3 Installing the Dome 3.3.4 Installing SD Card (optional) Press the reset button to start WPS pairing; press and hold the reset button for 10 s to reset the camera to factory settings. IPC-D1B20P-W/IPC-D1B20N-W...
  • Page 17: Attaching Device

    IPC-D1B40P-W/IPC-D1B40N-W 3.3.5 Attaching Device Make sure the mounting surface is strong enough to hold at least three times of the weight of the device and bracket.
  • Page 18 Cable going through the mounting surface...
  • Page 19: Adjusting Lens Angle

    Cable going through the side cable tray 3.3.6 Adjusting Lens Angle...

This manual is also suitable for:

Ipc-d1b20p-wIpc-d1b20n-wIpc-d1b40p-wIpc-d1b40n-w

Table of Contents