Table of Contents
Advertisement
Quick Links
Libretto di Istruzioni (IT)
Instruction booklet (EN)
(AR)
Mode d'emploi (FR)
Bedienungsanleitung (DE)
Instruktionsvejledning (DA)
Manual de instrucciones (ES)
Instrukcja (PL)
Manual de lnstruções (PT)
Instructiehandleiding (NL)
Bruksanvisning (NO)
Руководство по эксплуатации (RU)
Instruktionshandbo (SE)
Ohjekirja (FI)
Advertisement
Table of Contents
Related Manuals for Smeg KV90XE
Summary of Contents for Smeg KV90XE
- Page 1 Libretto di Istruzioni (IT) Instruction booklet (EN) (AR) Mode d’emploi (FR) Bedienungsanleitung (DE) Instruktionsvejledning (DA) Manual de instrucciones (ES) Instrukcja (PL) Manual de lnstruções (PT) Instructiehandleiding (NL) Bruksanvisning (NO) Руководство по эксплуатации (RU) Instruktionshandbo (SE) Ohjekirja (FI)
-
Page 2: Installation
• When the hood is taken out of its packaging inspect it to ensure that it is intact. If the product is damaged, do not use it and contact the Smeg assistance service. • Before making any connections, make sure that the mains voltage corresponds to the voltage shown on the label located inside the appliance. - Page 3 the dangers it entails. • Children must be supervised to ensure that they do not play with the appliance • ATTENTION: The accessible parts can become very hot if they are used with cooking equipment. MAINTENANCE • Before carrying out any maintenance procedure or cleaning, disconnect the appliance from the electricity supply.
-
Page 4: Installation Instructions
INSTALLATION INSTRUCTIONS: The hood is supplied with all the accessories necessary for its installation. The minimum distance between the lower surface of the hood and the hob must be at least 650mm for electric hobs (Fig. 1). If the motor inlet is equipped with a non-return valve for fumes, make sure it can open and close freely. -
Page 5: Electric Connection
Leave the motor inlet free. Install the active carbon filters as shown on page 8. If the hood is not supplied with an active carbon filter you must buy it separately at your nearest authorised Smeg dealer. For some models there is a standard set of fittings (fig.6) to... - Page 6 USER INSTRUCTIONS • CONTROLS UNIT For an optimal and efficient use of the product it is advisable to start the hood a few minutes before you start cooking and to keep it on for at least 15min after you have finished cooking or until steam and odours have completely disappeared. To start the hood, identify the command type of the hood and then follow the relative indications: SLIDER:...
- Page 7 2-DIGIT 10-KEY CAPACITIVE PUSHBUTTON BOARD: Function Display Turns the suction motor on / off. Displays the set speed Decreases the operation speed. Displays the set speed Increases the operation speed. Displays the set speed Activates the Intensive speed from any speed even with the motor off, this speed is timed.
-
Page 8: Optional Functions
1-DIGIT CAPACITIVE PUSHBUTTON BOARD: FUNCTION DISPLAY SWITCH THE SUCTION MOTOR ON / OFF. DISPLAYS THE SET SPEED DECREASE THE OPERATING SPEED DISPLAYS THE SET SPEED DISPLAYS THE SET SPEED INCREASE THE OPERATING SPEED FLASHING TIMED INTENSIVE START TIMED INTENSIVE SPEED SPEED TURN THE LIGHTING SYSTEM ON AND OFF ENABLES THE AUTOMATIC SHUTDOWN DELAY OF 15'... - Page 9 N.B. In some countries, the 4-speed version is also available, with the layout shown on the right, where: Filters Reset Key FUNCTIONS AND MAINTENANCE: Before performing any maintenance and/or cleaning always disconnect the hood from the power supply Regular cleaning guarantees good operation and a long appliance service life. The grease filters and filter hoods with carbon filters require special care.
-
Page 10: Replacement Lamps
In the case of the disc filter, simply tilt the two filters by 90° as shown in (fig.A) and then extract them from their housing. In the case of a cartridge filter attached with springs, (fig.B) exert the pressure required to counteract the resistance of the spring and then remove the filter In the case of a cartridge filter blocked with a bracket and threaded knob, (fig. -
Page 11: Weee Disposal
WEEE DISPOSAL: Pursuant to art. 26 of the Italian Legislative Decree dated 14 March 2014, no. 49 "Implementation of directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE)" The crossed out wheeled bin symbol on the equipment or its packaging indicates that the product at the end of its useful life must be collected separately from other waste.