Table of Contents
Advertisement
CEMENT MIXER
MODEL H5697
INSTRUCTION MANUAL
COPYRIGHT © NOVEMBER, 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#5904 PRINTED IN CHINA
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE
CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE MACHINE, THIS
MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES. PRE-
VIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
Advertisement
Table of Contents
Related Manuals for Grizzly H5697
Summary of Contents for Grizzly H5697
- Page 1 INSTRUCTION MANUAL COPYRIGHT © NOVEMBER, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #5904 PRINTED IN CHINA ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED.
- Page 2 WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. •...
-
Page 3: Table Of Contents
Handle & Dump Lever ...15 Drum...16 SECTION 5: OPERATIONS ...17 Operations ...17 SECTION 6: MAINTENANCE ...18 Lubrication ...18 Cleaning the Mixer ...18 V-Belts ...18 SECTION 7: REFERENCE INFO ...19 H5697 Data Sheet ...19 H5697 Parts Breakdown and Parts Lists ...20 Warranty and Returns ...22... -
Page 4: Section 1: Safety
H5697 Cement Mixer VISITORS... - Page 5 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories. H5697 Cement Mixer 15. USE RECOMMENDED ACCESSORIES. 16. REDUCE THE RISK OF UNINTENTION- LENGTH 17. MANY WOODWORKING TOOLS CAN...
-
Page 6: Additional Safety For Cement Mixers
BE AWARE THAT CEMENT, MORTAR, GROUT, AND ALL SILICATE DUSTS PRESENT A SERIOUS RESPIRATORY HAZARD WHEN THEY ARE AIRBORNE. Protect yourself by always wearing a res- pirator approved to guard against these kinds of dusts. CLEANING. H5697 Cement Mixer... -
Page 7: Section 2: General Information
We are also pleased to provide this manual with the Model H5697. It was written to guide you through assembly, review safety considerations, and cover general operating procedures. It repre- sents our latest effort to produce the best docu- mentation possible. -
Page 8: Section 3: Circuit Requirements
Circuit Breaker ...10 Amp, 1 Pole Plug Type The Model H5697 is supplied with a 5-15 plug, similar to Figure 1. Figure 1. Typical type 5-15 plug and receptacle. Grounding... -
Page 9: Section 4: Set Up
Wear safety glasses dur- ing the entire set up process! The Model H5697 is a heavy machine (106 lbs. shipping NOT over-exert yourself while unpacking or mov- ing your machine—get assistance. - Page 10 In the event that any nonproprietary parts are missing (e.g. a nut or a washer), we would be glad to replace them, or, for the sake of expedi- ency, replacements can be obtained at your local hardware store. H5697 Cement Mixer...
-
Page 11: Hardware Recognition Chart
Hardware Recognition Chart H5697 Cement Mixer... -
Page 12: Stand & Yoke
Using the yoke support, connect the front legs of the two stand assemblies together with (4) M10-1.5 x 25 carriage bolts, (4) 10mm ext tooth washers, and (4) M10-1.5 hex nuts (see Figure 8 on the next page). Cross Brace Corner Braces H5697 Cement Mixer... -
Page 13: Drive System
Driving end plate and inside cover Figure 9. installed and supporting rear end of yoke . Tighten all of the stand bolts that you left loose during assembly. H5697 Cement Mixer Yoke Support Components and Hardware Needed Splash Guard ...1 Motor Mount ...1... - Page 14 Figure 13. Installing upper pulley into yoke. Secure the upper pulley shaft to the upper pulley with the (4) M6-1 x 20 Phillips head screws (Figure 14). Figure 14. Upper pulley installed and properly secured to upper pulley shaft. H5697 Cement Mixer...
- Page 15 Figure 16. Attaching switch box to the outside pulley with the existing screws in the switch box. H5697 Cement Mixer 12. Place the outside pulley cover over the inside cover and secure it in place with the (4) M5- .8 x 10 Phillips head screws, as shown in...
-
Page 16: Wheels
Use (2) M8-1.25 x 20 hex bolts, (2) 8mm exterior tooth washers, and (2) 8mm flat washers on the ends of the axles to secure the wheels in place (Figure 21). Figure 21. Wheel installed on axle. H5697 Cement Mixer... -
Page 17: Handle & Dump Lever
(4) M8-1.25 hex nuts (Figure 22). Figure 22. Handle and handle brace installed on front of stand assembly. H5697 Cement Mixer Install the stop plate on the dump lever so the curved side is facing down, using (2) M10-1.5 x 30 hex bolts, (2) 10mm exterior... -
Page 18: Drum
(Figure 24). -16- Figure 24. Spanner nuts securing drum to yoke. ⁄ turn. Using the Phillips head screws, secure the pinion gear safety guard to the yoke, so that it is directly over the pinion gear. H5697 Cement Mixer... -
Page 19: Section 5: Operations
The maximum working capacity of this mixer is 2.5 60lb premix bags or 1.2 cubic feet. The Model H5697 is operated by a paddle switch. Pull the switch up to start the motor, and push the switch down to stop the motor. -
Page 20: Section 6: Maintenance
If you do, allow the compo- nents to thoroughly dry before plugging in the motor. • The easiest way to clean the cement mixer is by hosing it out with water. • Always clean the mixing drum immediately after using it. -
Page 21: Section 7: Reference Info
Warranty/Return information for the Model H5697. If you have any comments regarding this manual, please write to Grizzly at the address below: Grizzly Industrial, Inc. Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Customer Service #: (570) 546-9663 •... -
Page 22: H5697 Parts Breakdown And Parts Lists
-20- H5697 Parts Breakdown Motor Sub-Components 61-4 61-3 61-1 61-2 H5697 Cement Mixer... - Page 23 HEX BOLT M8-1.25 X 20 PH5697038 AXLE PH5697039 SLIDE BRACE PH5697040 AXLE BRACE PSS06M SET SCREW M8-1.25 X 16 PB07M HEX BOLT M8-1.25 X 25 H5697 Cement Mixer H5697 Parts List PART # PTLW09M PN03M PH5697045 PH5697046 PVM50 PSS20M PS09M PH5697050...
-
Page 24: Warranty And Returns
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom. - Page 25 Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:__________________________________________________...
- Page 26 FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...
- Page 28 Buy Direct and Save with Grizzly Visit Our Website Today And Discover Why • • • ® – Trusted, Proven and a Great Value! Grizzly ® Is The Industry Leader! SECURE ORDERING ORDERS SHIPPED WITHIN 24 HOURS E-MAIL RESPONSE WITHIN ONE HOUR...