Grizzly H8172 Owner's Manual

Cement mixer

Hide thumbs Also See for H8172:

Parts breakdown (3 pages)

Owner's manual (28 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

MODEL H8172

CEMENT MIXER

OWNER'S MANUAL

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TR9030 PRINTED IN CHINA

Table of Contents

Summary of Contents for Grizzly H8172

Page 1 MODEL H8172 CEMENT MIXER OWNER'S MANUAL COPYRIGHT © APRIL, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #TR9030 PRINTED IN CHINA...
Page 2 �� ...
Page 3: Table Of Contents
Table of Contents INTRODUCTION ... 2 Foreword ... 2 Machine Data Sheet ... 2 Contact Info ... 2 SECTION 1: SAFETY... 3 Safety Instructions for Machinery ... 3 Additional Safety for Cement Mixers ... 5 SECTION 2: CIRCUIT REQUIREMENTS ... 6 110V Operation ...
Page 4: Introduction
INTRODUCTION Foreword We are proud to offer the Model H8172 Cement Mixer. This machine is part of a growing Grizzly family of fine machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer...
Page 5: Section 1: Safety
�� H8172 Cement Mixer �� ...
Page 6 �� H8172 Cement Mixer...
Page 7: Additional Safety For Cement Mixers
If normal safety precautions are overlooked or ignored, seri- ous personal injury may occur. H8172 Cement Mixer ENTANGLEMENT. The spinning drum and engaging gears present an entanglement hazard. When using the cement mixer, tie...
Page 8: Section 2: Circuit Requirements
DO NOT connect the machine to the power source until instructed to do so. Amperage Draw The Model H8172 motor draws the following amps under maximum load: Motor Draw ... 8 Amps Circuit Recommendations...
Page 9: Section 3: Setup
Get lifting help or use power lifting equipment such as a fork lift to move heavy items. H8172 Cement Mixer Unpacking Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you...
Page 10: Inventory
Some hardware/fasteners on the inventory list may arrive pre-installed. Check mount- ing locations before assuming that any items from the inventory list are missing. NOTICE H8172 Cement Mixer...
Page 11: Assembly
�� Figure 4. Support leg installation. H8172 Cement Mixer Connect the upper and lower plunger rods together with an M6-1 x 25 hex bolt and M6- 1 lock nut, then insert the cotter pin where shown in Figure 5. Bend each leg of the cot- ter pin outward so it can't fall out.
Page 12 Repeat this process on the fasten- ers used in Steps 9–10, as well. Figure 10. Lower end of mixing blades attached to lower drum. H8172 Cement Mixer...
Page 13: Test Run
Figure 12. Upper part of mixing blades attached to upper drum. H8172 Cement Mixer 11. Slide the motor assembly onto the bearing block shaft, then secure the motor assembly to the frame (Figure 13). Use two 8mm flat washers, lock washers, and hex nuts on the motor assembly studs.
Page 14: Section 4: Operations
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training. -12-...
Page 15: Section 5: Maintenance
Since most oils are too thick to spray, use a mixture of half oil and half diesel fuel. This is a common spray mixture used in commer- cial concrete construction to prevent sticking. H8172 Cement Mixer Cleaning • Always unplug the cement mixer before cleaning.
Page 16: Wiring Diagram
�� Figure 16. Switch wiring. -14- Wiring Diagram �� H8172 Cement Mixer...
Page 17: Parts Breakdown
�� H8172 Cement Mixer Parts Breakdown �� ...
Page 18: Parts Breakdown
S CAPACITOR 30MFD 300VAC MOTOR FAN MOTOR COVER PHLP HD SCR M10-1.5 X 20 PVC WASHER 10MM LOCK WASHER 10MM MIXING BLADE HEX NUT M10-1.5 FLAT WASHER 10MM SHORT GEAR GUARD BEARING BLOCK GEAR GUARD HEX BOLT M8-1.25 X 70 H8172 Cement Mixer...
Page 19: Safety Labels Breakdown
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. H8172 Cement Mixer ��...
Page 20: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 21 �� ...
Page 22 �� ...
Page 24 �� ...

Grizzly H8172 Owner's Manual

Introduction

Section 1: Safety

Section 2: Circuit Requirements

Section 3: Setup

Section 4: Operations

Section 5: Maintenance

Warranty and Returns

Quick Links

Related Manuals for Grizzly H8172

Summary of Contents for Grizzly H8172

Table of Contents