Related Manuals for Showgear PSA-125A4C
Summary of Contents for Showgear PSA-125A4C
- Page 1 USER MANUAL ENGLISH PSA-125A4C Product code: 50667 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
- Page 2 PSA-125A4C Preface Thank you for purchasing this Showgear product. The purpose of this user manual is to provide instructions for the correct and safe use of this product. Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
-
Page 3: Table Of Contents
PSA-125A4C Table of contents Introduction ................................3 Before Using the Product ..........................3 Intended Use ............................... 3 Text Conventions ..............................3 Symbols and Signal Words ..........................4 Symbols on the Information Label ........................4 Safety ..................................5 Warnings and Safety Instructions ........................5 Requirements for the User .......................... -
Page 4: Introduction
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer. Your shipment includes: Showgear PSA-125A4C User manual Fig. 01 Intended Use This device is intended for professional use as a 3-phase power distribution unit in theaters, entertainment facilities, public venues, and similar. -
Page 5: Symbols And Signal Words
PSA-125A4C Symbols and Signal Words Safety notes and warnings are indicated throughout the user manual by safety signs. Always follow the instructions provided in this user manual. Indicates an imminently hazardous situation which, if not avoided, will result in DANGER death or serious injury. -
Page 6: Safety
PSA-125A4C Safety Important Read and follow the instructions in this user manual before installing, operating or servicing this product. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. Warnings and Safety Instructions... - Page 7 PSA-125A4C Attention General safety ● Do not shake the device. Avoid brute force when installing or operating the device. ● If the device is dropped or struck, disconnect the device from the electrical power supply immediately. If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it on immediately.
-
Page 8: Requirements For The User
PSA-125A4C Requirements for the User DANGER This product may not be used by ordinary persons. This product may be used only by instructed or skilled persons. Installation and maintenance can be carried out by instructed or skilled persons. Service shall be carried out only by skilled persons. Contact your Highlite International dealer for more information. -
Page 9: Description Of The Device
PSA-125A4C Description of the Device The PSA-125A4C is a 3-phase power distribution unit, providing real-time voltage and amperage information during your show. It has 4 5-pin CEE outputs and a 5-pin CEE input. The maximum allowed current load is 125 A per phase. The maximum allowed current load per output is 3 x 63 A. -
Page 10: Back View
PSA-125A4C Back View Fig. 03 5-pin CEE OUT 1 5-pin CEE OUT 2 5-pin CEE OUT 3 5-pin CEE OUT 4 5-pin CEE power IN Product code: 50667... -
Page 11: Product Specifications
PSA-125A4C Product Specifications Model: PSA-125A4C Electrical: Rated current: 125 A MCB rated current: 63 A MCB class: Class C MCB poles: Conductors: Inputs/Outputs: Power connector IN: 1 x CEE male 125 A 3P+N+PE, 400 V AC, 50/60Hz Power connector OUT:... -
Page 12: Installation
PSA-125A4C Installation Safety Instructions for Installation WARNING Incorrect installation can cause serious injuries and damage of property. Installation must be carried out only by instructed or skilled persons. Follow all applicable European, national and local safety regulations concerning electrical installations. -
Page 13: Schematic Overview
PSA-125A4C Schematic Overview Fig. 05 Setup and Operation Warnings and Precautions Attention Connect all cables before supplying power. Disconnect power supply before connecting or disconnecting cables. Safety Instructions for Operation Attention This device must be used only for the purposes it is designed for. -
Page 14: Start-Up
PSA-125A4C Start-up Connect the device to the power supply using the 5-pin CEE connector IN (13). Move the residual-current device (01) to ON position. Move the main circuit breakers (02/03/04/05) to ON position. Connect external devices to the 5-pin CEE connectors OUT (09/10/11/12). -
Page 15: Basic Cleaning Instructions
PSA-125A4C Basic Cleaning Instructions To clean the device, follow the steps below: Disconnect the device from the electrical power supply. Allow the device to cool down for 5 minutes. 03) Clean the device with a soft, lint-free cloth. Attention ●... - Page 16 ©2021 Showgear...
Need help?
Do you have a question about the PSA-125A4C and is the answer not in the manual?
Questions and answers