Subscribe to Our Youtube Channel
Related Manuals for TKH 921
Summary of Contents for TKH 921
- Page 1 Installation and Maintenance Instructions Runway Guard Lights - type 921 LED AGL 03-71087 Airfield Ground Lighting V2.0...
- Page 2 TKH Airport Solutions 2022 All rights reserved for TKH Airport Solutions. No part of this publication may be reproduced, modified, stored in a retrieval system, or transmitted, by any means or in any form without the written permission of the copyright owner.
-
Page 3: Table Of Contents
7 Adjustment..........................19 7.1 Aligning the Fixtures..........................19 7.1.1 Directional Alignment of Elevated Fixtures................. 20 7.1.2 Operation.............................22 7.1.3 Storage............................24 Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved. -
Page 4: About This Manual
TKH Airport Solutions reserves the right to revise this document without notification. The data provided in this document is based on the most recent information at the time of publication. TKH Airport Solutions is continually seeking to ensure that its products are developed to the latest technological standards. -
Page 5: Terms And Abbreviations
Version : V2.0 Language : English (Original manual) For the latest version of this document see https://www.tkh-airportsolutions.com/airfield-products/ or scan: Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved. -
Page 6: Safety Instructions
Use of this equipment in ways other than described in the datasheet and this manual may result in personal injury, death, or property damage. TKH Airport Solutions cannot be held responsible for injuries or damage resulting from non-standard, unintended application of its equipment. This equipment is designed and intended only for the purpose described in this manual. -
Page 7: Installation
Failure to follow these safety procedures can result in personal injury or death. • Allow only qualified personnel to install TKH Airport Solutions and auxiliary equipment. Use only approved equipment. Using unapproved equipment in an approved system may void agency approvals and will void the warranty. -
Page 8: Action In The Event Of A System Or Component Malfunction
Allow only qualified personnel to make repairs. Repair or replace the malfunctioning component according to instructions provided in its manual. Allow only qualified personnel to perform maintenance, troubleshooting, and repair tasks. Only persons who are properly trained and familiar with TKH Airport Solutions equipment are permitted to service this equipment. -
Page 9: About The Runway Guard Lights - Type 921
2” (60 mm) stake mounting (Type C) or with 2” thread stub (Type A). Electronics The driver electronics for the LED modules are identical to the electronics used in TKH Airport Solutions unidirectional LED light fixture type 792. -
Page 10: Configurations
• Special 230 V RGL trafo is needed (Type K921920) • Output options 15%, 30% and 100% light intensity Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved. -
Page 11: Accessories
Accessories Optional: • 792.119 - Adjustment kit for alignment RGL-921 Spare Parts Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved. - Page 12 182.780-00 Trafo for 230 V RGL K-921920 Label at position 6 indicates program version or type of Flash operation. Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved.
-
Page 13: General Recommendations
Failure to earth the base correctly will void the warranty for all damages occurring as a result of voltage surges. Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 ©... -
Page 14: Installation
Installation Unpacking the RGL-921 Unpack the equipment and make sure that nothing is broken before starting installation. The RGL-921 light fixtures are not pre-adjusted in the factory and must be adjusted before taking into operation. Installation in the Field Connect the pre-adjusted light fixture electrically. -
Page 15: Maintenance
The light assemblies are delivered fully tested and sealed. In case of malfunctioning during the warranty period, the defective light shall be shipped back to TKH Airport Solutions without opening it. Any attempt to open the light during the warranty period will void the warranty. -
Page 16: Changing The Front Glass
The hole in the rim (a) must be covered by the spring (b). Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved. -
Page 17: Replacing The Complete Led Light Unit
Unplug the power supply cable from the LED light unit. Disconnect the earth wire from the LED light unit. Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved. - Page 18 Insert the new LED light unit into the yellow housing. Close the spring locks. Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved.
-
Page 19: Adjustment
Alignment telescope tool kit 792.118 (including mounting accessories) Never look at the sun through the optical sights - it may permanently damage your eyes. Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved. -
Page 20: Directional Alignment Of Elevated Fixtures
Adjust the elevation by inserting the upper blue cable pin into the hole for the required vertical angle. Mount the telescope kit: Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved. - Page 21 Figure 2: Toe-in plate labelled with 0°, +/- 2°, +/- 3°, and +/- 3.5° The figures show examples of toe-in: Toe-in 0° Toe-in 2° left Toe-in 2° right Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved.
-
Page 22: Operation
Aim the vertical center line of the telescope reticle at the center of the next fixture in the row. Figure 3: Aim for the next fixture in the row Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 ©... - Page 23 At the fixtures furthest away from the runway, turn the rifle scope 180°, or follow Method 2. Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved.
-
Page 24: Storage
Dismount the telescope by loosening the butterfly nut. Replace the dust cap and store the device in its case in a clean and dry environment. Installation and Maintenance Instructions - LED AGL Runway Guard Lights - type 921 © TKH Airport Solutions 2022. All rights reserved. - Page 25 Company profile: TKH Airport Solutions is an innovator in airfield ground lighting, offering a complete range of LED AGL products. We build upon the know-how from a long and successful tradition of pioneering developments in the AGL and connectivity industry. Being part of the TKH Group, our company can build on a history of more than 90 years in smart connectivity, energy distribution and AGL.
Need help?
Do you have a question about the 921 and is the answer not in the manual?
Questions and answers