Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
O
i
riginal
nstructiOns
c
g
e
D
Ommercial
as Or
lectric
ryer
m
Xcem2765
Xcgm2765
ODels
anD
INSTRUCTIONS D'INSTALLATION
i
'
nstructiOns D
Origine
s
-l
À
èche
inge
gaz Ou électrique À usage cOmmercial
m
Xcem2765
Xcgm2765
ODèles
et
INSTRUCCIONES DE INSTALACIÓN
i
nstrucciOnes Originales
s
ecaDOra a gas O eléctrica cOmercial
m
Xcem2765
Xcgm2765
ODelOs
y
ISTRUZIONI D'INSTALLAZIONE
i
struziOni Originali
a
sciugatrice a gas O elettrica cOmmerciale
m
Xcem2765
Xcgm2765
ODelli
e
www.whirlpoolcommerciallaundry.com
W10868678A
Advertisement
Related Manuals for Whirlpool XCEM2765
Summary of Contents for Whirlpool XCEM2765
- Page 1 INSTALLATION INSTRUCTIONS riginal nstructiOns Ommercial as Or lectric ryer Xcem2765 Xcgm2765 ODels INSTRUCTIONS D’INSTALLATION ’ nstructiOns D Origine À èche inge gaz Ou électrique À usage cOmmercial Xcem2765 Xcgm2765 ODèles INSTRUCCIONES DE INSTALACIÓN nstrucciOnes Originales ecaDOra a gas O eléctrica cOmercial...
- Page 2 MAINTENANCE INSTRUCTIONS..........6 INSTRUCTIONS D’ENTRETIEN ..........26 IF YOU NEED ASSISTANCE ........... 6 SI VOUS AVEZ BESOIN D'ASSISTANCE ......26 FOR WHIRLPOOL AUTHORIZED SERVICE PERSON POUR LE PERSONNEL D’ENTRETIEN AUTORISÉ PAR WHIRLPOOL TOOLS & PARTS ..............7 OUTILS ET PIÈCES ..............27 DIMENSIONS/CLEARANCES ..........
- Page 3 This is an additional safety alert symbol that alerts you to the risk of fire. WARNING “Risk of Fire” - Clothes dryer installation and service must be performed by a Whirlpool authorized installer. - Install the clothes dryer according to the manufacturer’s instructions and local codes.
- Page 4 • If you cannot reach your gas supplier, call the fire department. – Installation and service must be performed by a Whirlpool authorized installer, Whirlpool authorized service agency, or the gas supplier. IMPORTANT: When discarding or storing your old clothes dryer, remove the door.
- Page 5 ■ The interior of the dryer and dryer exhaust vent should ■ children without supervision. be cleaned periodically by Whirlpool authorized service WARNING: The appliance must not be supplied through ■ personnel. an external switching device, such as a timer, or connected See “Electrical Requirements”...
- Page 6 IF YOU NEED ASSISTANCE If you need help, contact the dealer from whom you purchased the appliance, or a Whirlpool designated service company. When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.
- Page 7 TOOLS & PARTS Tools Needed: 203 mm (8") 203 mm (8") or 254 mm (10") Flat-Blade Screwdriver Phillips Screwdriver or 254 mm (10") Adjustable Wrench Pipe Wrench that opens to 25 mm ( 1") Torx T-20 Security 25 mm (1") Hex-Head 8 mm ( 5⁄16") Socket Wrench Pliers (that open to †...
- Page 8 DIMENSIONS/CLEARANCES Dimensions Side View Back View " 27" (743 mm) (686 mm) 26" (660 mm) Electric " " (343 mm) (210 mm) 36" 41" (914 mm) (1042 mm) " (electric models) (273 mm) " " (38 mm) (953 mm) 4" dia (gas models) (102 mm) 35"...
- Page 9 DRYER INSTALLATION REQUIREMENTS Location Requirements Recessed Area and Closet Installation Instructions This dryer may be installed in a recessed area or closet. For recessed area and closet installations, minimum clearances can be found on the warning label on the rear of the dryer or in “Dimensions/Clearances.”...
- Page 10 INSTALLING LEVELING LEGS 2. Screw in leveling legs Examine leveling legs and find diamond marking. Screw legs into leg holes by Diamond Marking hand. Use an adjustable wrench or 25 mm (1") hex-head socket wrench to finish turning legs until diamond Foot marking is no longer visible.
- Page 11 LEVELING Leveling your dryer properly reduces excess noise and vibration. 2. Grip dryer from top and rock back and forth, making sure all four legs are firmly on floor. Repeat, rocking dryer from side to side. If dryer rocks, go to Step 3 and adjust leveling legs. 1.
- Page 12 This dryer is supplied without an electric cord and plug. It This is 3-wire appliance which must be earthed. must be connected by a Whirlpool authorized service person Do not earth to a gas pipe. to a single-phase electricity supply at the voltage shown...
- Page 13 GAS DRYER INSTALLATION REQUIREMENTS Electrical Requirements EARTHING INSTRUCTIONS IMPORTANT: Observe all governing codes and ordinances. You will need a grounded electrical outlet located within 610 mm (2 feet) of either side of the dryer. This dryer is supplied/fitted with an electrical supply cord and plug.
- Page 14 Gas conversion must be done by a Whirlpool authorized gas service technician. Conversion kit, part number (W10181947) is available for purchase from your dealer. Full instructions are supplied with...
- Page 15 DRYER VENTING REQUIREMENTS Elbows: 45° elbows provide better airflow than 90° elbows. ■ Good Better Clamps: Use clamps to seal all joints. ■ Exhaust vent must not be connected or secured with screws ■ WARNING: To reduce the risk of fire, this dryer MUST BE or other fastening devices that extend into interior of duct EXHAUSTED OUTDOORS.
- Page 16 DRYER VENTING REQUIREMENTS Vent Hoods 102 mm (4") Diameter Exhaust Hoods Exhaust hood must be at least 305 mm (12") from the ground or any object that may be in the path of the exhaust (such as flowers, rocks, bushes, or snow). Box Hood Louvered Hood Angled Hood...
- Page 17 A clean-out cover should be located on the main vent for periodic cleaning of the vent system. NOTE: For more dryer venting information, please refer to Whirlpool document W10100920. GAS SUPPLY CONNECTION (on some models) Make Gas Connection 2.
- Page 18 30 mbar Factory Adjusted Pressure (G30/G31): NOTE: Conversion kit: From Natural Gas to LP Gas - Europe: Whirlpool Part No. W10233219. Conversion kit: From Natural Gas to LP Gas - Australia: Whirlpool Part No. W10315369. Conversion kit: From Natural Gas to Natural Gas - France/Belgium: Whirlpool Part No. W10181947.
- Page 19 COMPLETE INSTALLATION 6. Check dryer operation (some accumulated time may be 1. Check the electrical requirements. Be sure that you have on the timer due to factory testing). Close dryer door. Insert the correct electrical supply and the recommended earthing coins in slide and press slide in slowly.
- Page 20 REVERSING DRYER DOOR SWING (OPTIONAL) You can change your door swing from a right-side opening 7. Be certain to keep cardboard spacer centered between doors. Reattach outer door panel to inner door panel so to left-side opening, if desired. handle is on the side where hinges were just removed. Remove the Door Assembly 1.
- Page 21 DRYER DISPOSAL MODEL NOMENCLATURE: CGM – Whirlpool Gas FQ – Series Revision CEM – Whirlpool Electric 2765 – Model Type Number...
- Page 22 DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you should ask your retailer about buying an extended warranty.
- Page 23 ©2017 All rights reserved. ©2017 Tous droits réservés. W10868678A ©2017 Todos los derechos reservados. ©2017 Tutti i diritti riservati. 04/17...
Need help?
Do you have a question about the XCEM2765 and is the answer not in the manual?
Questions and answers