Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DHP485STE
Summary of Contents for Makita DHP485STE
- Page 1 INSTRUCTION MANUAL Cordless Hammer Driver Drill DHP485 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DHP485 Drilling capacities Masonry 13 mm Steel 13 mm Wood 38 mm Fastening capacities Wood screw 6 mm x 75 mm Machine screw No load speed High (2) 0 - 1,900 min Low (1) 0 - 500 min Blows per minute High (2) 0 - 28,500 min... -
Page 3: Ec Declaration Of Conformity
When operating a power tool outdoors, use an WARNING: The vibration emission during actual extension cord suitable for outdoor use. Use of use of the power tool can differ from the declared a cord suitable for outdoor use reduces the risk of emission value depending on the ways in which the electric shock. - Page 4 Battery tool use and care Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. Use power tools only with specifically desig- nated battery packs. Use of any other battery packs may create a risk of injury and fire.
-
Page 5: Tips For Maintaining Maximum Battery Life
DO NOT let comfort or familiarity causing fires, personal injury and damage. It will with product (gained from repeated use) replace also void the Makita warranty for the Makita tool and strict adherence to safety rules for the subject charger. product. MISUSE or failure to follow the safety... -
Page 6: Functional Description
Indicating the remaining battery FUNCTIONAL capacity DESCRIPTION Only for battery cartridges with the indicator CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge CAUTION: Always switch off the tool before... -
Page 7: Overheat Protection
Overheat protection NOTE: When the tool is overheated, the tool stops automatically and the lamp starts flashing. In this When the tool/battery is overheated, the tool stops case, release the switch trigger. The lamp turns off in automatically. In this situation, let the tool/battery cool one minute. before turning the tool on again. -
Page 8: Adjusting The Fastening Torque
CAUTION: Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the "1" side and "2" side, the tool may be damaged. CAUTION: Do not use the speed change lever while the tool is running. -
Page 9: Installing Hook
Installing driver bit holder ASSEMBLY Optional accessory CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing driver bit/ drill bit Optional accessory ► 1 . -
Page 10: Screwdriving Operation
Blow-out bulb Optional accessory ► 1 . Vent Screwdriving operation ► 1 . Blow-out bulb CAUTION: Adjust the adjusting ring to the After drilling the hole, use the blow-out bulb to clean the proper torque level for your work. dust out of the hole. CAUTION: Make sure that the driver bit is Drilling operation... -
Page 11: Maintenance
Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. - Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885653-220 www.makita.com 20180321...