Huawei SUN2000-6KTL-L1 Quick Manual

Huawei SUN2000-6KTL-L1 Quick Manual

Hide thumbs Also See for SUN2000-6KTL-L1:

Advertisement

Quick Links

SUN2000-(2KTL-6KTL)-L1
Quick Guide
Issue: 06
Part Number: 31500DQD
Date: 2020-12-02
HUAWEI TECHNOLOGIES CO., LTD.
0

Advertisement

Table of Contents
loading

Summary of Contents for Huawei SUN2000-6KTL-L1

  • Page 1 SUN2000-(2KTL-6KTL)-L1 Quick Guide Issue: 06 Part Number: 31500DQD Date: 2020-12-02 HUAWEI TECHNOLOGIES CO., LTD.
  • Page 2 The screw is used to secure the DC switch to prevent accidental startup. The screw is delivered with the solar inverter. • b: DC input terminals PV1 and PV2 are controlled by the DC switch. Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
  • Page 3: Installing The Device

    Installing the Device Installation Requirements Space Angle Mounting Hole Dimensions Installing the Solar Inverter 1. Install the mounting bracket. Avoid drilling holes in the water pipes and cables buried in the wall.
  • Page 4 • M6x60 expansion bolts are delivered with the solar inverter. If the length and number of the bolts do not meet installation requirements, prepare M6 stainless steel expansion bolts by yourself. • The expansion bolts delivered with the solar inverter are mainly used for solid concrete walls. For other types of walls, prepare bolts by yourself and ensure that the wall meets the load bearing requirements of the solar inverter.
  • Page 5: Connecting Cables

    Connecting Cables Preparing Cables • Connect cables in accordance with the local installation laws and regulations. • Before connecting cables, ensure that the DC switch of the solar inverter and all the switches connected to it are set to OFF. Otherwise, the high voltage produced by the solar inverter may cause electric shocks.
  • Page 6 Installing a WLAN Antenna or Smart Dongle • If FE communication is used, install a WLAN-FE Smart Dongle (SDongleA-05). You need to purchase the WLAN-FE Smart Dongle by yourself. • If 4G communication is used, install a 4G Smart Dongle (SDongleA-03). You need to purchase the 4G Smart Dongle by yourself.
  • Page 7 (Optional) 4G Smart Dongle (4G Communication) • If your Smart Dongle is configured with a SIM card, you do not need to install the SIM card. The configured SIM card can be used only on the Smart Dongle. • If your Smart Dongle is not equipped with a SIM card, prepare a standard SIM card (size: 25 mm x 15 mm) with the capacity greater than or equal to 64 KB.
  • Page 8: Installing The Ac Output Power Cable

    Installing the AC Output Power Cable Ensure that the protective layer of the AC output power cable is inside the connector, that the core wires are totally inserted into the cable hole, and that the cable is connected securely. Failing to do so may cause device malfunction or damage. 1.
  • Page 9: Installing Dc Input Power Cables

    To remove the AC connector, perform the operations in reverse order of installing the AC connector. Then, remove the plug insert, as shown in the following figure. Plug insert Installing DC Input Power Cables 1. Ensure that the PV module output is well insulated to ground. 2.
  • Page 10 1. Assemble DC connectors. Positive connector Positive metal terminal PV-CZM-22100 Ensure that the cable cannot Negative Click be pulled out after being connector Negative metal terminal crimped. Use the wrench shown Ensure that cable in the figure to tighten polarities are correct. the locking nut.
  • Page 11 (Optional) Installing Battery Cables • Use insulated tools when connecting cables. • Connect battery cables with correct polarity. If battery cables are reversely connected, the solar inverter may be damaged. Assemble the positive and negative connectors by following the instructions in section 3.5 "Installing DC Input Power Cables."...
  • Page 12 COM Port Pin Definitions Label Definition Description RS485B, RS485 Solar inverters cascading 485B1 differential signal– scenario: used for connecting to the solar inverters. RS485A, RS485 485A1 differential signal+ RS485B, RS485 Used for connecting to the 485B2 differential signal– RS485 signal ports of the battery and power meter.
  • Page 13: Verifying The Installation

    Connecting Signal Cables Number of Communications Cables Click Verifying the Installation Acceptance Criteria The solar inverter is installed correctly and securely. The WLAN antenna is installed correctly and securely. Cables are routed properly as required by the customer. Cable ties are evenly distributed and no burr exists. The PE cable is connected correctly and securely.
  • Page 14: Powering On The System

    Powering On the System • Before turning on the AC switch between the solar inverter and the power grid, check that the AC voltage is within the specified range using a multimeter set to the AC position. • If the solar inverter is connected to a battery, turn on the DC switch within 1 minute after turning on the AC switch.
  • Page 15 Type Status (Blinking at long intervals: Meaning On for 1s and then Off for 1s; Blinking at short Intervals: On for 0.2s and then Off for 0.2s) Communication LED3 indication Blinking green at short intervals Communication is in progress. Blinking green at long intervals A mobile phone is connected to the solar inverter.
  • Page 16: Downloading The App

    Commissioning • The screenshots are for reference only. The actual screens prevail. • Obtain the initial password for connecting to the solar inverter WLAN from the label on the side of the solar inverter. • Set the password at the first login. To ensure account security, change the password periodically and keep the new password in mind.
  • Page 17 To create multiple installer accounts for a company, log in to the FusionSolar app and tap New User to create an installer account. Creating a PV Plant and a Plant Owner For details, see the FusionSolar App Quick Guide During the FusionSolar app upgrade, scan the QR code to download the correponding quick guide according to the...
  • Page 18 PV plant as prompted. 2. Log in to https://intl.fusionsolar.huawei.com to access the WebUI of the FusionSolar Smart PV Management System. On the Homepage page, click the plant name to go to the plant page.
  • Page 19: Setting Battery Parameters

    Scenario 2: Setting on the Solar Inverter Side (Solar Inverter Not Connected to the Management System) 1. If the solar inverter is not connected to the FusionSolar Smart PV Management System, access the Device commissioning screen (Refer to 7.1 Device Commissioning.) on the FusionSolar app to set the physical layout of Smart PV Optimizers.
  • Page 20: Device Commissioning

    Device Commissioning 1. Access Device commissioning. Scenario 1: Your phone is not Scenario 2: Your phone is connected to the Internet. connected to the Internet. When your phone is connected to the Internet, Device commissioning is not displayed after you tap ..
  • Page 21: Resetting The Password

    Resetting the Password 1. Ensure that the SUN2000 connects to the AC and DC power supplies at the same time. Indicators are steady green or blink at long intervals for more than 3 minutes. 2. Perform the following operations within 3 minutes: a.
  • Page 22: Customer Service Contact Information

    Customer Service Contact Region Country Phone Service Support Email France Germany Spain eu_inverter_support@huawei.com 0080033888888 Europe Italy Netherlands Other countries For details, see solar.huawei.com. Australia eu_inverter_support@huawei.com 1800046639 Turkey eu_inverter_support@huawei.com 0080021686868 Malaysia /1800220036 (+66) 26542662 (charged apsupport@huawei.com Asia Pacific by local call) Thailand...
  • Page 23 Huawei Technologies Co., Ltd Huawei Industrial Base, Bantian, Longgang Shenzhen 518129, People's Republic of China solar.huawei.com...

This manual is also suitable for:

Sun2000-2ktl-l1

Table of Contents