Page 1
USE AND CARE GUIDE AND INSTALLATION INSTRUCTIONS UNDER COUNTER REFRIGERATOR For questions about features, operation/performance, parts, accessories, or service, call: 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com. In Canada, call: 1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.ca. W11348447A...
TABLE OF CONTENTS INTRODUCTION Safety ........................3 Proper Disposal of Your Old Refrigerator ........4 Features ......................4 INSTALLATION REQUIREMENTS Tools and Parts ....................5 Location Requirements ................5 Product Dimensions ..................6 Custom Overlay Panel ................6 Handle (Optional)..................7 Electrical Requirements ................8 INSTALLATION INSTRUCTIONS Unpack the Refrigerator .................8 Custom Overlay Panel Installation ...........9 Installation and Door Closing ..............10 USING REFRIGERATOR...
INTRODUCTION SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER”...
PROPER DISPOSAL OF YOUR Stealth Flush Design with OLD REFRIGERATOR Smooth Close Door Create an unbroken silhouette. Discreet 1/8" reveals WARNING envelop every side, without exposed hinges or trim pieces. Quiet, soft, secure. An articulating hinge discreetly ushers the door open and gently pulls it Suffocation Hazard closed.
INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before starting installation TOOLS AND PARTS NEEDED: Phillips screwdriver Custom Overlay Door Panel — Refer “ Custom Overlay Panel Preparation.” Recessed Custom handle and mounting hardware (optional) receptacle PARTS SUPPLIED: locations...
PRODUCT DIMENSIONS SOLID DOOR OVERLAY PANEL — PREPARATION Create the custom overlay panel using the dimensions OVERALL PRODUCT shown in the illustration "Solid door overlay panel and Width (up to hinge cover) 237/8" (60.72 cm) hinge routing dimensions". Rout shaded areas to a 1/2" (12 mm) depth as shown.
HANDLE (OPTIONAL) GLASS DOOR OVERLAY PANEL — PREPARATION Create the custom overlay panel using the dimensions Custom handles are typically attached to the custom shown in the illustration " Glass door overlay panel and overlay door panel only. hinge routing dimensions". Rout shaded areas to a 1/2" Refer instructions received with JennAir RISE (12 mm) depth as shown.
ELECTRICAL REQUIREMENTS Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection. WARNING RECOMMENDED GROUNDING METHOD A 115 V, 60 Hz, AC only, 15 or 20 A fused, grounded electrical supply is required.
CUSTOM OVERLAY PANEL INSTALLATION Using two people, hold the custom overlay panel against the door. Be sure that the top and bottom IMPORTANT: hinges fit accurately into the routing on back of the custom wood panel. Create custom overlay panel according to the specifications in the “Custom Overlay Panel”...
INSTALLATION AND DOOR CLOSING Plug into a grounded 3 prong outlet. Move the refrigerator into its final location. Your refrigerator has four leveling legs. If your refrigerator seems unsteady or you want the door to close more Turn the leveling legs to the right to lower the easily, adjust the refrigerator’s tilt using the instructions refrigerator, or turn the leveling legs to the left to below.
USING REFRIGERATOR CONTROLS NOTE: NOTE: The control panel is located at the top of the The default recommended temperature for the compartment and facing front. refrigerator is 37°F (2°C). The set point range for this model is 32°F to 42°F (0°C to 5°C). The control of the refrigerator has no mechanical parts or buttons.
REFRIGERATOR SHELVES Auto Light (Glass Door Models) The refrigerator has a sensor that will turn on the TO REMOVE OR ADJUST UPPER SHELVES: interior display light automatically when someone Remove the shelf by lifting it up and out of the shelf walks by.
DOOR BINS (SOLID DOOR MODELS) LIGHTS Your refrigerator has two door bin locations for maximum The refrigerator has an interior light that illuminates storage capacity. when the door is opened. TO REMOVE AND REPLACE THE DOOR BINS: NOTE: The light is an LED which does not need to be replaced.
Using a Phillips screwdriver, remove the two screws. to prop it open far enough for air to get in. This stops odor and mold from building up. Remove the base grille. TO REPLACE THE BASE GRILLE: MOVING CARE Open the refrigerator door. When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.
Is the food packaged correctly? Check that all food THE DOOR WILL NOT CLOSE COMPLETELY is securely wrapped. Wipe off damp food containers Are food packages blocking the door open? before placing in the refrigerator. Rearrange containers so that they fit more tightly and Is the control set correctly for the surrounding take up less space.
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED TO OBTAIN WARRANTY SERVICE. JENNAIR ® Please have the following information available when you call the Customer eXperience Center: REFRIGERATION Name, address, and telephone number LIMITED WARRANTY Model number and serial number A clear, detailed description of the problem Proof of purchase including dealer or retailer name and address IF YOU NEED SERVICE:...
Page 17
DISCLAIMER OF IMPLIED WARRANTIES IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you.
Need help?
Do you have a question about the JUGFR242HM00 and is the answer not in the manual?
Questions and answers