Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Woods BSS54
Summary of Contents for Woods BSS54
- Page 1 BOX SCRAPERS BSS54 BSS60 BSS65 BSS72 BSM72 BSM84...
-
Page 2: Introduction
TO THE OWNER: Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate. -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ..........2 SPECIFICATIONS . -
Page 4: Specifications
SPECIFICATIONS BSS54 BSS60 BSS65 BSS72 BSM72 BSM84 Width 54" 60" 65" 72" 84" Height to Top Link Pin 34" 34" 34" 34" 34" 34" Depth 29.6" 29.6" 29.6" 29.6" 29.6" 29.6" Number of Cutting Edges Cutting Edge Size 1/2" x 6"... -
Page 5: Safety Rules
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Power unit must be equipped with ROPS or Safety is a primary concern in the design and ROPS cab and seat belt. Keep seat belt securely manufacture of our products. Unfortunately, our fastened. - Page 6 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Watch for hidden hazards on the terrain during Always wear relatively tight and belted clothing operation. to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective ...
-
Page 7: Safety Decals
Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637. - Page 8 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 3 – 55121 4 - 1003751 8 Safety MAN0761 (11/14/2008)
-
Page 9: Operation 9
OPERATION The operator is responsible for the safe operation of this CONNECTING BOX SCRAPER TO TRACTOR equipment. The operator must be properly trained. Oper- ators should be familiar with the equipment, the tractor, and all safety practices before starting operation. Read the safety rules and safety decals on page 5 through page 7. - Page 10 Quick Hitch Connection SCARIFYING NOTICE 1. Place the scarifier shanks in position with the points facing toward the tractor. The 3/4" bolt and sleeve in the lower hole provide ■ the attachment point for a Category 1 quick coupler. 2. Lock into position with the lock pins provided. The Do not remove this bolt and sleeve when operating lower shank position provides the greatest ground the scraper.
-
Page 11: Storage
CLEANING 3. If a pressure washer is used, follow the advice of the pressure washer manufacturer. After Each Use ● Inspect machine and replace worn or damaged parts. Remove large debris such as clumps of dirt, grass, ● Sand down scratches and the edges of areas of ●... -
Page 12: Owner Service
OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety information in this manual. ARNING ... - Page 13 REPLACING SCARIFIER SHANK TOOTH REPLACING CUTTING EDGE 1. Remove scarifier shank from the scarifier bar. All box scraper models use two 1/2" x 6" (12.7 x 152 mm) cutting edges. They are interchangeable and reversible. 2. Refer to Figure 7. Remove the worn tooth by driving a chisel between the shank (1) and tooth (2).
- Page 14 ASSEMBLY DEALER SET-UP INSTRUCTIONS Assembly of this Box Scraper is the responsibility of the WOODS dealer. It should be delivered to the owner completely assembled and adjusted for normal condi- tions. Complete the Check Lists on page 15 before delivering the attachment to the customer.
-
Page 15: Dealer Check Lists 15
DEALER CHECK LISTS PRE-DELIVERY CHECK LIST front tractor wheels. When adding weight to attain 20% of tractor and equipment weight on (Dealer's Responsibility) front tractor wheels, you must not exceed the ROPS weight certification. Weigh the tractor Inspect the equipment thoroughly after assembly to be and equipment. - Page 16 BSS/BSM BOX SCRAPER 9. - Safety Decal Set 10. - Complete Decal Set 11. - Quick Hitch Cat 1/2 Bushing Kit 16 Parts MAN0761 (11/7/2008)
-
Page 17: Parts List
BSS/BSM BOX SCRAPER PARTS LIST DESCRIPTION DESCRIPTION SU105 2 Drawbar pin w/lynch pin 1004635 4 Scarifier & tip (BSS54) HBL233 2 Cat 2 Drawbar pin 1004635 5 Scarifier & tip (BSS60 / BSS65) 1029092 1 Mast plate - right (BSS) 1004635 6 Scarifier &... -
Page 18: Bolt Torque Chart
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. -
Page 19: Bolt Size Chart & Abbreviations
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 Metric Bolt Thread Sizes 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............. Agriculture MPa............Mega Pascal ASABE ....American Society of Agricultural &... -
Page 20: Replacement Parts Warranty
Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice. - Page 21 The limited warranty covers any defects in the material and/or workmanship. Following the proper, recommended installation by an authorized Woods Dealer and normal use of a Woods mounting and backhoe or loader, if a tractor incurs damage resulting from the attachment, Woods will cover the existing tractor warranty in the event the manufacturer voids its tractor warranty because of the attachment.
- Page 22 Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respec- tive companies or mark holders. Specifications subject to change without notice.