Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zanussi ZDS12002WA
Summary of Contents for Zanussi ZDS12002WA
- Page 1 User Manual GETTING STARTED? EASY. ZDS12002WA EN User Manual Dishwasher...
-
Page 2: Safety Information
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. -
Page 3: Safety Instructions
Put the cutlery in the cutlery basket with the sharp ends • pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to •... - Page 4 • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. SERVICE • Contact the Authorised Service Centre to repair the appliance. We recommend only the use of original spare parts. •...
-
Page 5: Easy Start
EASY START On/off indicator Delay button Programme marker Programme knob Indicators Start button INDICATORS End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates. -
Page 6: Information For Test Institutes
PROGRAMMES Consumption values Degree of soil Programme Programme phases Type of load Duration Energy Water (min) (kWh) Normal soil • Prewash 0.778 Crockery and • Wash 50 °C cutlery • Rinses • Heavy soil • Prewash 160 - 1.1 - 1.3 13-14 Crockery, cut- •... -
Page 7: Adjusting The Water Softener
SETTINGS ADJUSTING THE WATER SOFTENER The programme marker must be in position. 1. Press and hold and simultaneously turn the knob counterclockwise until the programme marker is in position. 2. Release when and Delay start to flash. • The current setting is indicated by the number of flashes of the indicator (e.g. -
Page 8: Activating Airdry
German degrees French degrees Water softener mmol/l Clarke degrees (°dH) (°fH) level 4 - 10 7 - 18 0.7 - 1.8 5 - 12 <4 <7 <0.7 < 5 1) Factory setting 2) Do not use salt at this level. ACTIVATING AIRDRY AirDry improves the drying results with less energy consumption. -
Page 9: Before First Use
The programme marker must be in position. 1. Press and hold and simultaneously turn the knob counterclockwise until the programme marker is in position. 2. Release when and Delay start to flash. 3. Turn the knob counterclockwise until the programme marker is in position. -
Page 10: Adding Rinse Aid
CAUTION! Water and salt can come out of the salt container during filling. To prevent corrosion, start a programme immediately after filling the salt container. ADDING RINSE AID The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. -
Page 11: Adding Multi-Tablets
ADDING MULTI-TABLETS • Do not fill the salt container and the rinse aid dispenser. • Set the rinse aid dispenser to the lowest position. PROGRAMME SELECTION MODE The appliance must be in Programme selection mode to start a programme. If the control panel does not show this condition, do the Reset. -
Page 12: Option Delay
1. Open the water tap and close the door. 2. Select a programme. 3. Press OPTION DELAY With this option you can postpone the start of a programme by 3 hours. 1. Set the programme. 2. Press Delay. 3. Press to start the countdown. -
Page 13: Hints And Tips
AT THE END OF THE PROGRAMME 5 min The indicator is on. After 5 minutes of non-use, the appliance enters standby mode and all the indicators are off. It decreases energy consumption. 1. Turn the knob to 2. Close the tap. HINTS AND TIPS GENERAL THE WATER SOFTENER... -
Page 14: Troubleshooting
• Detergent tablets do not fully dissolve with short • Make sure that cutlery and dishes do not bond programmes. To prevent detergent residues on together. Mix spoons with other cutlery. the tableware, we recommend that you use the • Make sure that glasses do not touch other tablets with long programmes. - Page 15 Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The programme does not start. •...
-
Page 16: The Washing And Drying Results Are Not Satisfactory
Problem and alarm code Possible cause and solution The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneous- ly all the appliances in use. Check the socket am- perage and the capacity of the meter or turn off one of the appliances in use. -
Page 17: Care And Cleaning
Problem Possible cause and solution The interior of the appliance is • This is not a defect of the appliance. it is caused by the hu- wet. midity in the air that condenses on the walls. Unusual foam during washing. •... -
Page 18: Technical Information
CLEANING THE FILTERS • Make sure that there are no residues of food or soil in or around the edge of the sump. • Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. •... -
Page 19: Environmental Concerns
Capacity Place settings Power consumption Left-on mode (W) Power consumption Off-mode (W) 0.50 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. - Page 20 WWW.ZANUSSI.COM/SHOP...