Subscribe to Our Youtube Channel
Related Manuals for Repotec RP-1000SC
Summary of Contents for Repotec RP-1000SC
- Page 1 1000Base-T to 1000Base-SX/LX Gigabit Ethernet Media Converter Quick Installation Guide...
-
Page 2: Fcc Class A Certification
FCC Class A Certification This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when equipment operated... -
Page 3: About Media Converter
Introduction Thank you for choosing the 1000Base Gigabit Ethernet Media Converter, The Converter introduced here provides one channel media conversion between 1000BASE-TX and 1000BASE-SX/LX. About Media Converter Media Converter is a network technology specified by IEEE 802.3ab and IEEE 802.3z 1000BASE-TX and 1000BASE-SX/LX standards. -
Page 4: Installation
Installation This chapter gives step-by-step installation instructions for the Converter. Selecting a Site for the Equipment As with any electric device, you should place the equipment where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements: The ambient temperature should be between 32 and 104 degrees Fahrenheit (0 to 40 degrees... -
Page 5: Connecting To Power
Connecting to Power This Converter is a plug-and-play device. Connect the supplied AC to DC power adaptor with a power voltage of 9Vdc/0.7Amp to the DC-Jack on the converter, and then attach the plug into a standard AC outlet. Installing in a Chassis The Converter can be fit into any of the expansion slots on a special designed chassis. -
Page 6: Monitoring The Converter Through Management Module
Monitoring the Converter through Management Module There is a management module that can control this media converter through the chassis system, this media converter can be controlled through Web Browser, SNMP and terminal emulation program. The management module will detect the default reset on the DIP switches and display out the status, also the management module can control the function through the chassis system. -
Page 7: Led Indicator
LED Indicator The LED indicators give you instant feedback on status of the converter: LEDs State Indication Lights on Power on Power (PWR) Lights off Power off Lights on Linking Link and Activity Lights Blinking Data transmitting and receiving (LINK/ACT) Lights off Not Linking... -
Page 8: Link Pass Through Function
Link Pass Through Function LLCF (Link Loss Carry Forward) When a device connected to the converter and the TP line loss the link, the converter’s fiber will disconnect the link of transmit, so that the other ends will know that there is a linkage error on this end. - Page 9 LLR (Link Loss Return) When a device connected to the converter and the fiber line loss the link, the converter’s fiber will disconnect the link of transmit. There is a switch to enable or disable the function of the media converter. The table below shows how LLR function is working: Media Converter Auto-Negotiation...
- Page 10 Switch 1 : On -> Forced Mode Off -> Auto Negotiation mode Switch 2 : On -> LLR enable Off -> LLR disable Switch There is a two pin DIP switch on the module which define as switch 1 and switch 2: Switch 1: Fiber mode switch When the switch was turned to “On”, it means that the fiber was turned to forced mode, and “Off”...
-
Page 11: Specifications
Specifications Standards: IEEE802.3ab 1000BASE-TX IEEE802.3z 1000BASE-SX/LX Data Transfer Rate: 1488000pps for 1000Mbps Duplex Mode: Full Duplex Mode LED indicators: PWR, LNK/ACT Cable 1000BASE-T -- 4 pair Cat. 5, EIA/TIA-568 100-ohm screened twisted-pair (STP), up to 100m 1000BASE-SX -- 50/125μm multi-mode fiber optic cable, up to 550m 1000BASE-LX -- 9/125μm or 10/125μm single-mode fiber optic... -
Page 12: Ordering Information
Ordering Information Please include the following information when ordering: 1. Fiber type: multi-mode or single-mode 2. Fiber connector type: SC 3. Segment distance range for the fiber port TX port Connector Cabling Segment Distance Type RJ-45 Copper Wire Max. 100 m FX port Connector Cabling...
Need help?
Do you have a question about the RP-1000SC and is the answer not in the manual?
Questions and answers