1. Manuals
  2. Brands
  3. Fransgard Manuals
  4. Winches
  5. V-3004
  6. Manual

Fransgard V-3004 Manual

Farm tractor winch
Hide thumbs
Table of Contents

Advertisement

Quick Links

Fransgård
Manual
US
V-3004
Farm tractor winch

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V-3004 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Fransgard V-3004

Summary of Contents for Fransgard V-3004

  • Page 1 Fransgård Manual V-3004 Farm tractor winch...
  • Page 2 Fransgård Maskinfabrik A/S Fredbjergvej 132 DK - 9640 Farsø Telefon : +45 98 63 21 22 : +45 98 63 18 65 www.fransgard.dk mail@fransgard.dk...

  • Page 3: Table Of Contents

    Adjusting the clutch ..................4 Instructions for mounting the wire .............. 5 Safety manual ..................6-15 Spare part list ..................16- Technical data V-3004 TECHNICAL SPECIFICATIONS Pulling power ..............3000 kg/6600 lbs. Clutch ..................... 315 cm². Transmission ..............5/8" roller chain.

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS LUBRICATION AND MAINTENENCE The machines may only be used by Lubricate the PTO. shaft once daily. qualified operators. Lubricate the chain once every week. Before starting working, check that the No oil on clutch lining (15509). tractor and the machines are standing on a The turning plate at the top pulley has to fixed horizontal base.

  • Page 5: Danger / Warning

    DANGER! Read before operation this machine! It is the owner’s responsibility to instruct all equipment operators and support personal in the operation of winch. WARNING! 13) Operate the winch from a control rope at Do not attempt to operate this winch least 6 m.

  • Page 6: Adjusting The Clutch

    ADJUSTING THE CLUTCH The clutch is adjusted at the factory. If it is necessary to adjust it do so as follows: 1. Loosen lock nut no. 34 and bolt no. 1. 2. Hold lever no. 29 against stop, tighten both bolts no. 1 until slight resistance is felt. 3.

  • Page 7: Instructions For Mounting The Wire

    Instructions for mounting the wire. 1.) Pull about 1 metre of the wire 1 out through hole 2 and back through hole 3 and out through hole 4. 2.) Mount the wire fixing block 5 (making sure that only 5 mm of the wire are introduced into the fixing block) and fasten with the allen screw and the unbraco wrench supplied.

  • Page 8: Safety Manual

    Safety, Maintenance and Operation Tips for North American winch Models: V3004 – V3507 - V4000 – V-5000 and V6500 NOTICE: THIS SECTION MUST BE READ PRIOR TO USING THIS MACHINE The owner’s operator and repair manual, included with the machine, must also be read prior to using this machine Failure to heed the warnings printed on the winch or in the owner’s manual might result serious PHYSICAL injury.
  • Page 9 SAFETY INSTRUCTIONS The machines may only be used by qualified operators. Prior to operating this winch, make sure that the tractor and the winch are on a stable, level surface, to avoid tipping over, when the unit is under load. The user is responsible for assuring that no unauthorized persons are in the working area.
  • Page 10 Fransgard uses a specially designed cable that resists abrasion from being dragged on the ground. Therefore it is highly recommended that an original Fransgard wire cable be used as a replacement for a LONGER WEARING LIFE AND BETTER VALUE FROM YOUR PURCHASE.
  • Page 11 Installing the Chokers/Sliders: After installing the cable, release 4 – 5 ft. of cable, by unlocking the cable drum locking latch which is running on the cable drum sprocket. Remove the bolt joining the two pieces of the choker/slider. Place the rounded part on the cable, then slip the flat slotted part in between the rounded part and tighten with the bolt and Nylon lock nut.
  • Page 12 Winching: Lower the winch so that it rests on the butt plate. Activate the tractor PTO set it to run at approx. 500 rpm. Unlock the cable drum, by pulling the cable drum latch. Pull out the desired length of cable towards the logs that are to be pulled. Tie the forestry chain around the log, and lock the forestry chain either on to the hook or in the slot of the slider/choker, which has been previously installed properly on the cable( as per Fig.
  • Page 13 (Warrington seal). This cable is designed specifically for this application since most cables are not designed to be dragged on the ground, stones etc. These are just a few of the several reasons why you should demand and only use Fransgard genuine replacement parts when servicing your product.
  • Page 14 Clutch Adjustment:  The friction clutch system is adjusted at the factory prior to shipment.  Under normal conditions it should perform without any adjustment for well over 1000 working hours.  If it is noted that the clutch is slipping with minimal loads, even though the green power cord is fully pulled, so the clutch arm rests against the stop, then a clutch adjustment may be necessary.
  • Page 15 DO’S AND DONT’S FOR SAFETY AND LONGER MACHINE WEAR DANGER! WARNING! Read the original manual before operation this machine! It is the owner’s responsibility to instruct all equipment operators and support personnel in the operation of winch. FOR OPERATING WINCH: 1) Keep hands, feet and clothing away from power driven parts! 2) Ensure that the cable is in good conditions before operating the winch.
  • Page 16 DO NOT: 1) Do not attempt to operate this winch without proper training and knowledge of the working features of this winch 2) Do not operate this machine until the owner’s manual has been completely read and understood. New owner’s manual are available from your Dealer or the factory phone + 45 98 63 21 22 (North America: 450 654 6126).
  • Page 17 Delivery Check List Winch Model: ___________ Serial No.: ____________ Dealer Check List on delivery of winch PTO cut and installed on tractor with proper overlap of Safety guard and shafts to prevent the Shaft from “binding” or “ bottoming-out” when the winch is raised with the three-point hitch The three-point hitch is to be adjusted properly so that the Protection screen does not hit the tractor cabin when the winch is raised 3) Operating and Safety Instructions reviewed with Purchaser...
  • Page 18 -15-...
  • Page 19 Varenr. Antal Bemærkninger Part no. Quantity Remarks Teil Nr. Anzahl Bemerkung No.de pièce Nombre Beskrivelse Desceiption Bezeichnung Designation Remarques 740210560 Sætskrue Set screw Schraube M16x50mm. FZB 15502 Kobling Clutch Kupplung Embrayage 15503 Nagle Bolzen Rivet 15504 Koblingsarm Clutch Kupplung Embrayage 15539 Fjeder Spring...
  • Page 20 -18-...
  • Page 21 Varenr. Antal Bemærkninger Part no. Quantity Remarks Teil Nr. Anzahl Bemerkung No.de pièce Nombre Beskrivelse Description Bezeichnung Designation Remarques 15587 Lås m.unbrakobolt Locking wedge Riegelkeil Clavette de blocage 15537 Nylonsnor String Draht Cordon 8mm - 6mtr. 740320016 Møtrik Mutter Ecrou M16 - 6KT FZB 740420012 Låsemøtrik...
  • Page 22 -20-...
  • Page 23 Varenr. Antal Bemærkninger Part no. Quantity Remarks Teil Nr. Anzahl Bemerkung No.de pièce Nombre Beskrivelse Desceiption Bezeichnung Designation Remarques 740210310 Bolt Bolt Bolzen Boulon M10x25 FZB 113020 Skive Disk Scheibe Bague Ø11xØ30x2,0mm. FZB 18006 Topstangbolt Bolt Bolzen Boulon Kat.1-2 1210080 Traktorsplit Cotter Splint...

Table of Contents