Temperature Controls - Frigidaire FFWC4222QS Use & Care Manual

•
The default temperature for the wine cooler is 54°F (12°C). The temperature after power failure will be the
temperature set before the power failure.
• To prolong the life of compressor, please wait for at least 5 minutes before the wine cooler is restarted after power
failure.
Failure display
•
If "E" and "F" are displayed, please contact local service personnel for repair.
• If the temperature in the cooler is too low, it will display "L".
• If the temperature in the cooler is too high, the screen will display "H" and will flash. Under this state, the buzzer
will buzz for 30 seconds. One minute later, the buzzer will continue to buzz for the next 30 seconds. After three
times, the alarm will not buzz any more. You can press any key to cancel sound alarm.
•
Storing too many wine bottles in the cooler may cause the temperature in the cooler to rise temporarily.
Temperature Control for Dual Zone Model
Indication of Temperature in Lower Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
Indication of Temperature in Lower Chamber
Indication of Temperature in Upper Chamber
Temperature in lower chamber indicator
lower
zone
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature increase 1°C.
Press this button once to increase temperature 1° F/C.
: Press this button once and the temperature decrease 1°C.
: Press this button once and the temperature decrease 1°C.
Press this button once to decrease temperature 1° F/C.
Indication of Temperature in Upper Chamber
upper
Temperature in upper chamber indicator
zone
: Temperature display.
: Press this button once and the temperature increase 1°C.
Press this button once to increase temperature 1° F/C.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
: Press this button once and the temperature decrease 1°C.
Press this button once to decrease temperature 1° F/C.
Power: On/off button used to turn on/off all load.
The wine cooler can be operated by adjusting the temperature control buttons (up arrow and down arrow) until
Press Light and Power together for 2 seconds and you can convert between
: Temperature display.
the desired temperature is reached.
fahrenheit temperature and Celsius temperature.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
The display will flash for a few seconds before set point is locked in.
Power: On/off button used to turn on/off all load.
Notice!
•
Press Light and Power together for 2 seconds and you can convert between The default temperature is 46°F (8°C) for upper zone and 59°F (15°C) for lower zone. The temperature after
power failure will be the temperature set before the power failure.
fahrenheit temperature and Celsius temperature.
The default temperature is 10/10°C, and the temperature after power
• To prolong the life of compressor, please wait for at least 5 minutes before the wine cooler is restarted after power
failure will be the temperature set before the power failure.
failure.
To elongate the service life of compressor, please wait for at least 5
Notice!
The temperature range MIN and MAX is 41 - 54° F for the upper zone and 54 - 64° F for the lower zone.
The default temperature is 10/10°C, and the temperature after power
minutes before the wine cooler is restarted after power failure.
Failure display
failure will be the temperature set before the power failure.
•
If "E" and "F" are displayed, please contact local service personnel for repair.
Failure display
To elongate the service life of compressor, please wait for at least 5 • If the temperature in the cooler is too low, it will display "L".
If there is failure on the sensor, the screen may display failure code, such
• If the temperature in the cooler is too high, the screen will display "H" and will flash. Under this state, the buzzer
minutes before the wine cooler is restarted after power failure.
will buzz for 30 seconds. One minute later, the buzzer will continue to buzz for the next 30 seconds. After three
as: E and F. When the screen displays the above-mentioned errors, please
times, the alarm will not buzz any more. You can press any key to cancel sound alarm.
Failure display
do not disassemble it for check by yourself. You should contact local
•
Storing too many wine bottles in the cooler may cause the temperature in the cooler to rise temporarily.
If there is failure on the sensor, the screen may display failure code, such
after-sales service personnel for repair.
as: E and F. When the screen displays the above-mentioned errors, please
If the temperature in the cooler is too low, it will display "L".
do not disassemble it for check by yourself. You should contact local
When the temperature in the cooler is too high, the screen will display "H"
after-sales service personnel for repair.
and will flash; under this state, the buzzer will buzz until 30 seconds; one
If the temperature in the cooler is too low, it will display "L".
minute later, the buzzer will continue to give alarm in the next 30 seconds; after

tEMpERAtuRE cOntROLS

Indication of Temperature in Lower Chamber
: Press this button once and the temperature in
: Press this button once and the temperature dec
Indication of Temperature in Upper Chamber
: Press this button once and the temperature in
: Press this button once and the temperature dec
Temperature display
: Temperature display.
Light: This LED turns the light ON and OFF.
Light: Lighting button for LED lamp; it controls the on/o
Power: This LED turns the power ON and OFF.
Power: On/off button used to turn on/off all load.
Press both Light and Power LED's at the same time to
Press Light and Power together for 2 seconds and yo
change between fahrenheit and Celsius temperatures.
fahrenheit temperature and Celsius temperature.
Notice!
The default temperature is 10/10°C, and the te
failure will be the temperature set before the powe
To elongate the service life of compressor, ple
minutes before the wine cooler is restarted after po
Failure display
If there is failure on the sensor, the screen may di
as: E and F. When the screen displays the above-m
do not disassemble it for check by yourself. Yo
after-sales service personnel for repair.
If the temperature in the cooler is too low, it will dis
When the temperature in the cooler is too high, th
and will flash; under this state, the buzzer will buzz
minute later, the buzzer will continue to give alarm in th
the alarm is given for three times, it will not give ala
7