Related Manuals for Gigabyte SW016A
Summary of Contents for Gigabyte SW016A
- Page 1 User’s Manual 16/24-port 10/100Mbps Auto-Negotiation Smart Switches (Version 1.5)
- Page 2 FCC Class A Compliance This equipment generates and uses radio frequency energy. If it is not installed and used properly in strict accordance with the manufacturer’s instructions, it may cause interference to radio and television reception. It has been type-tested and found to comply the specifications in sub- part J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.
- Page 3 Checklist: Check the contents of your package for following parts: 16/24-port 10/100M Fast Ethernet Smart Switch Power Cord and Accessory User’s Manual Console Port Cable (option) If any of these pieces are missing or damaged, please contact your dealer immediately, If possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.
-
Page 4: Table Of Contents
Contents Introduction------------------------------------------1 Features and Specifications-------------------------2 Hardware Description------------------------------- 4 Front Panel Rear Panel Hardware Installation---------------------------------6 Configuration------------------------------------------7 10/100M bps(Server)Switching 10/100M bps(Hub)Switching Switch Operation--------------------------------------8 Address Table Learning Forwarding & Filtering Store-and-Forward Auto-Negotiation Hardware Troubleshooting PAGE... -
Page 5: Introduction
This 16/24-port Ethernet switching is a highly reliable network switch and is the ideal device for bridging Ethernet to Fast Ethernet workgroups or networks. Simple and cost-effective, the 16/24-port Ethernet Switching supports IEEE802.3u, IEEE802.3,... -
Page 6: Features And Specifications
Features and Specifications Features: 16/24-port 10/100mbps TX Auto-Negotiation Ethernet Switch Complies with the IEEE802.3 Ethernet and IEEE802.3u Fast Ethernet standard Features Store-and-Forward mode with wire-speed filtering and forwarding rates Full/Half-Duplex capability on every TX ports, total bandwidth is up to 200Mbps port... - Page 7 Specifications: Comply IEEE802.3/IEEE802.3u/IEEE802.3x Network Media 100Base-TX-UTP/STP category 5 cable 10Base-T-UTP/STP category 3 or 5 cable Connector: STP RJ-45port for 10/100Mbps TX LED indicators: Power (per unit) Link/Activity, Speed, and Duplex/Collision (per port) Dimension: 16-Port Rack-mountable 440mm(L) ×200mm(W) × 45mm(H) 16-Port Desktop 300mm(L) ×116mm(W) ×45mm(H) 24-Port Rack-mountable 440mm(L) ×200mm(W) ×...
-
Page 8: Hardware Description
Hardware Description This section describes the hardware features of the 16/24-port Ethernet Switching. For Easier management and control of the switch, familiarize yourself wide its display indicators, and ports, Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the hub, read this chapter carefully. - Page 9 LED indicators LED Function Color Description Green ON: Power on LINK/ACT Green ON: Indicates the adapter is connected to hub Flash: Indicates data in or out the port 10/100 Green ON: 100Mbps OFF: 10Mbps Module Green ON: 100Base-FX module installed (24s only) FDX/COL Green ON: Full Duplex...
-
Page 10: Rear Panel
AC inlet, which accepts 100-240VAC 50-60Hz power input and one module option. On 24-Port switch, the fiber optic module is designed to share with the 24th TP port, do not simultaneously use 24th TP port and fiber optic module. And 16th TP port is shared with the optic module on 16-port switch. -
Page 11: Hardware Installation
Hardware Installation Place the 16/24-Ethernet Switching on a smooth surface. Connect the output of power cord to the AC-inlet of 16/24-port Ethernet Switch. Connect hub or PC to one port of the 16/24-port Ethernet Switching using Category 3/4/5 UTP/STP cabling. -
Page 12: Configuration
Configuration 100Mbps Server to 10Mbps Hub 1. Plug one end of the Category 5 UTP Cable into any one port of the 16/24-port Ethernet switching. And the other end of this cable into the RJ-45 of Fast Ethernet Adapter in the server. The cable length between these 2 connecting points should not exceed 100meter. -
Page 13: Switch Operation
Switch Operation Address Table The 16/24-port Ethernet Switching is implemented with an address table. The address table composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. This... -
Page 14: Store-And-Forward
However, the switch is most commonly used to segment existing hubs, which nearly always improves overall performance. A Ethernet Switching can be easily configured in... -
Page 15: Auto-Negotiation
Auto-Negotiation The STP port on the 16/24-port switch hub have built-in “Auto- negotiation”. This technology automatically sets the best possible bandwidth when a connection is established with another network device (usually at Power On or Reset).This is done by detect the modes and speeds at the second of both... -
Page 16: Hardware Troubleshooting
16/24-port Ethernet Switching was set up according to instruction in this manual. The Link LED is not lit Solution: a. Make sure the switch configuration is consistent with the connecting device b. Check the cable connections. Performance is bad Solution: a. - Page 17 Hub’s RJ- 45 Pin Assignments Station Ports 1-8 Input Receive Data+ Input Receive Data- Output Transmit Data+ Output Transmit Data- 4,5,7,8 Not used Schematics for both straight and crossover twisted-pair cable are shown below. (Note that crossover cable is only required if you cascade hubs via the RJ-45 station ports;...
Need help?
Do you have a question about the SW016A and is the answer not in the manual?
Questions and answers