Table of Contents

Advertisement

Available languages

Available languages

Quick Links

WOOD BURNING FIREPLACE
OWNER'S OPERATION AND INSTALLATION MANUAL
PFS
®
C
US
ICC-ES #ESR-2542
MODELS (V)B36, (V)B36I, (V)B36L, AND (V)B36LI
SAVE THIS BOOK
This book is valuable. In addition to instructing you
on how to install and maintain your appliance, it also
contains information that will enable you to obtain re-
placement parts or accessory items when needed. Keep
it with your other important papers.
This fireplace is approved for use as a wood burning fire-
place or for use with a vented gas log approved to ANS
Z21.60, Z21.84 standards or for use with a vent-free gas log
heater approved to ANS Z21.11.2 standard. A FMI PROD-
UCTS, LLC hood must be installed when using a vent-free
log heater (see Accessories, page 18).
This wood burning fireplace complies with UL127-
CAN/ULC-S610-M87 standard as a FACTORY BUILT
APPLIANCE.
FOR CANADA: The authority having jurisdiction (such
as the municipal building department, fire department,
etc.) should be contacted before installation to deter-
mine the need to obtain a permit.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
For more information, visit www.fmiproducts.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the B36I and is the answer not in the manual?

Questions and answers

Summary of Contents for FMI B36I

  • Page 1 ANS Z21.60, Z21.84 standards or for use with a vent-free gas log heater approved to ANS Z21.11.2 standard. A FMI PROD- UCTS, LLC hood must be installed when using a vent-free log heater (see Accessories, page 18).
  • Page 2: Table Of Contents

    Before beginning installation of this fireplace, • Due to high temperatures, the read these instructions through completely. appliance should be located • This FMI PRODUCTS, LLC fireplace and out of traffic and away from its components are safe when installed furniture and draperies.
  • Page 3: Specifications

    SPECIFICATIONS 1" AIRSPACE TO COMBUSTIBLE MATERIAL NO COMBUSTIBLE MATERIAL ON FACE 0" TO TOP SPACERS AIR KIT GAS LINE KNOCK OUT KNOCK OUT COMBUSTIBLE WALL BOARD 0.75" AIR SPACE BACK AND 12.875" SIDES 8.125" 9.625" NOT LESS THAN 14" TO 10.188"...
  • Page 4: Fireplace Installation

    FIREPLACE INSTALLATION SELECTING LOCATION 3. Set fireplace directly in front of this open- ing and slide unit back until nailing flanges To determine safest and most efficient location touch side framing. for fireplace, you must take into consideration 4. Check level of fireplace and shim with the following guidelines: sheet metal if necessary.
  • Page 5 FIREPLACE INSTALLATION Continued HEARTH EXTENSION Seal Gap Fireplace Front A hearth extension projecting a minimum of 16" in front of and a minimum of 8" beyond each side of fireplace opening is required to Ember Protector protect combustible floor construction in front of fireplace.
  • Page 6 FMI PRODUCTS, LLC voids warranty. Fan within 9" of fireplace opening (and within 9" is operated by pressing rocker switch (see of top louver opening).
  • Page 7: Venting Installation

    Slip Section "* ET-8DM Square Chase-Top 12"* ET-8HT CHIMNEY PIPE Square Chase-Top FMI PRODUCTS, LLC chimney system ETO-8DM 12"* with Mesh consists of 12", 18", 24", 36" and 48" snap- ETL-8DM Square Chase-Top lock, double-wall pipe segments, planned 7" to 15"*...
  • Page 8 VENTING INSTALLATION Continued ASSEMBLY AND INSTALLATION OF installing double wall snap-lock chimney to- gether, it is important to assure joint between DOUBLE WALL CHIMNEY SYSTEM chimney sections is locked. Check by pulling Each double wall chimney section consists chimney upward after locking. Chimney will of a galvanized outer pipe, a stainless steel not come apart if properly locked.
  • Page 9 VENTING INSTALLATION Continued See Detail A Ceiling Support Pipe 12S-8DM 2" Min. See Detail B Straps Straps Straps Straps Detail A Detail B Return Elbow Angle Firestop Figure 10 - Ceiling Support Pipe 12S-8DM OFFSET RISE CHIMNEY LENGTH 48" 36" 24" 18" 12" "...
  • Page 10 VENTING INSTALLATION Continued FIRESTOP SPACERS (3600FS-8DM-1) 4. Remove shingles around opening mea- sured. Cut out this section. Firestop spacers are required at each point 5. Add next sections of pipe until end where chimney penetrates a floor space. penetrates roof line. Check to see that Their purpose is to establish and maintain proper clearances are maintained.
  • Page 11 VENTING INSTALLATION Continued Terminations with 16" slip pipe sections are Overlap Storm Collar Shingles Top available. RTT-8DM and RTTL-8DM are Flashing and Sides Only approved for flashing installations. When Cone needed, these adjustable terminations may Nail Only be used in combination with pipe assembly Outer to achieve correct chimney height.
  • Page 12 VENTING INSTALLATION Continued 10 FOOT RULE FINISHING FIREPLACE All flue gas outlet chimney terminations must Combustible materials, such as wallboard, extend a minimum of 3 feet in height above gypsum board, sheet rock, drywall, plywood, highest point where it passes through roof and etc., may make direct contact with sides and must be at least 2 feet above highest point of top around fireplace face.
  • Page 13: Optional Gas Line Installation

    OPTIONAL GAS LINE INSTALLATION Gas line hook up should be done by your Note: A FMI PRODUCTS, LLC hood must be supplier or a qualified service person. installed when using an unvented gas log set (see Accessories on page 18).
  • Page 14: Operation And Maintenance

    OPTIONAL GAS LINE INSTALLATION Continued WARNING: If the fireplace WARNING: When using has been used for wood burn- a decorative vented gas log, ing, firebox and chimney must damper must be removed or be cleaned of soot, creosote and permanently locked in fully open ashes be a qualified chimney position and glass doors must cleaner.
  • Page 15: Technical Service

    You may have further questions about instal- You can also visit our web site at lation, operation, or troubleshooting. If so, www.fmiproducts.com. contact FMI PRODUCTS, LLC at 1-866-328- 4537. When calling please have your model and serial numbers of your heater ready. www.fmiproducts.com...
  • Page 16: Parts

    PARTS WOOD BURNING FIREPLACE MODELS (V)B36, (V)B36I, (V)B36L, (V)B36LI www.fmiproducts.com 109034-01H...
  • Page 17 PARTS WOOD BURNING FIREPLACE MODELS (V)B36, (V)B36I, (V)B36L, (V)B36LI This list contains replaceable parts used in your fireplace. NO. PART NO. DESCRIPTION QTY. Insulation Pan • • Air Separator • • Firebox Top • • 111431-01 Air Deflector • •...
  • Page 18: Accessories

    ACCESSORIES DOUBLE WALL PIPE 12-8DM 12-8HT 18-8DM 18-8-HT 24-8DM 24-8HT 36-8DM 36-8HT 48-8DM 48-8HT BI-FOLD GLASS DOOR BDB36 - Black BDB36B - Brushed Brass BDB36P - Platinum ROOF FLASHING 0 TO 6/12 PITCH - V6F-8DM 6/12 TO 12/12 PITCH - V12F-8DM STORM COLLAR SC1-1 For RT-8DM and RTL-8DM ANTI-DRAFT SHIELD...
  • Page 19 ACCESSORIES Continued BLOWER KIT - BK OUTSIDE AIR KIT FOR FLOOR INSTALLATION AK4F ROUND TOP TERMINATIONS RT-8DM, RTL-8DM, RT-8HT, RLT-8HT SQUARE CHASE-TOP TERMINATION ROUND TOP TERMINATIONS WITH ET-8DM, ET-8DM, ET-8HT SLIP SECTION RTT-8DM, RTTL-8DM, RTT-8HT, RLTT-8HT SQUARE TOP TERMINATION WITH SLIP SECTION ETL-8DM, ETL-8DM, ETL-8HT OUTSIDE AIR KIT FOR SIDE WALL...
  • Page 20 2701 S. Harbor Blvd. Santa Ana, CA 92704 109034-01 1-866-328-4537 Rev. H www.fmiproducts.com 09/09...
  • Page 21 ANSI Z21.60, Z21.84 ou une bû- che à gaz sans système d'évacuation homologuée selon la norme ANSI Z21.11.2. Une hotte FMI PRODUCTS, LLC doit être installée si l'appareil est utilisé avec un appareil de chauffage à bûche sans système d'évacuation (voir Accessoires, page 20).
  • Page 22 • Ne laissez jamais les enfants procéder à l'installation de ce foyer. sans surveillance lorsqu'il y a • Ce foyer FMI PRODUCTS, LLC et ses pièces du feu dans le foyer. sont sûrs lorsqu'ils sont installés conformé- ment aux consignes de ce manuel. Vous créez...
  • Page 23: Caractéristiques

    CARACTÉRISTIQUES COUCHE D'AIR ENTRE LES MATÉRIAUX COMBUSTIBLES 2,5 CM (1 PO) AUCUN MATÉRIAU ENTRETOISES COMBUSTIBLE SUPÉRIEURES SUR LA FAÇADE 0 CM/PO DISQUE DÉFONÇABLE DISQUES DÉFONÇABLES DE LA DU PRÊT-À-MONTER DE CANALISATION GAINE D'AIR EXTÉRIEUR DE GAZ PANNEAU DE MUR COMBUSTIBLE COUCHE D'AIR, 32,7 cm...
  • Page 24: Installation Du Foyer

    INSTALLATION DU FOYER SÉLECTION D'UN EMPLACEMENT STRUCTURE Pour déterminer l'emplacement du foyer le 1. Les figures 1 et 2 contiennent les dimen- plus sûr et le plus efficace, vous devez tenir sions des ouvertures de la structure du compte des consignes suivantes : foyer.
  • Page 25 INSTALLATION DU FOYER suite Z (non fourni) doit être fabriqué selon la Espace de calfeutrage hauteur de la plateforme. Le protecteur Façade du foyer contre les braises doit dépasser sous le foyer d'une distance minimum de 4 cm (1 po). Le protecteur contre les braises doit Protecteur de braises être fabriqué...
  • Page 26 être situés à moins de 23 cm (9 L'utilisation de ventilateurs ou de souffleurs po) de l'ouverture du foyer et à moins de 23 cm autres que ceux qui sont fabriqués par FMI (9 po) de l'évent supérieur. Les matériaux com- PRODUCTS, LLC annulent la garantie. Le bustibles situés 23 cm (9 po) au dessus du foyer...
  • Page 27: Installation Du Système De Ventilation

    CONDUIT DE CHEMINÉE bustion de l'extérieur se fait par une galerie ventilée (AK4F) ou par un mur latéral (AK4). Le système de cheminée de FMI PRO- Consultez la figure 24 de la page 17 pour des DUCTS, LLC comprend des sections de instructions sur le fonctionnement du prêt-à-...
  • Page 28 INSTALLATION DU SYSTÈME DE VENTILATION suite Conduit ASSEMBLAGE ET INSTALLATION extérieur D'UN SYSTÈME DE CHEMINÉE À galvanisé de 31,4 cm DOUBLE PAROI Extrémité Chaque section de cheminée à double ourlée paroi consiste en un conduit extérieur galva- Conduit intérieur en acier nisé, un conduit de fumée intérieur en acier inoxydable de inoxydable et une entretoise métallique.
  • Page 29 INSTALLATION DU SYSTÈME DE VENTILATION suite UTILISATION DE COUDES DE 3. La longueur maximale du conduit entre les supports (coude de retour ou 12S-8DM) DÉCALAGE (30E-8DM) est 1,82 m (6 pi) de longueur d'angle. 1. Afin d'obtenir le décalage voulu, vous On peut installer un maximum de deux pouvez installer toute combinaison de sections de longueur d'angle de 1,82 m...
  • Page 30 INSTALLATION DU SYSTÈME DE VENTILATION suite TABLEAU DES DÉCALAGE MONTÉE LONGUEUR DE LA CHEMINÉE DÉCALAGES (HAUTEUR 122 cm 91,5 cm 61 cm 45,7 cm 30 cm DU SYSTÈME : 6,7 à 15,2 m (48 po) (36 po) (24 po) (18 po) (12 po) [22 à...
  • Page 31 INSTALLATION DU SYSTÈME DE VENTILATION suite ENTRETOISES DE PARE-FEU 2. Déterminez le point central sur la toiture. L'inclinaison est la distance que la toiture (3600FS-8DM-1) descend en fonction d'une portée don- Des entretoises de pare-feu sont nécessaires née, habituellement 30 cm (12 po). Une à...
  • Page 32 INSTALLATION DU SYSTÈME DE VENTILATION suite INSTALLATION DE SOLINS (V6F- Produit de Conduit de calfeutrage 8DM OU V12F-8DM) cheminée imperméable Déterminez les solins requis à l'aide du ta- bleau des ouvertures dans la toiture. Glissez Mitre les solins sur le conduit jusqu'à ce que la Solins base arrive à...
  • Page 33 INSTALLATION DU SYSTÈME DE VENTILATION suite Des terminaisons avec section coulissante de RÈGLE DE TROIS MÈTRES (DIX 40,6 cm (16 po) sont disponibles. Les modè- PIEDS) les RTT-8DM et RTTL-8DM sont approuvés Toutes les terminaisons de sortie de conduit pour les installations de solins. S'il y a lieu, ces de fumée doivent dépasser d'au moins 91 cm terminaisons réglables peuvent être utilisées (3 pi) au-dessus du point le plus élevé...
  • Page 34: Installation D'une Canalisation De Gaz En Option

    INSTALLATION DU SYSTÈME DE VENTILATION suite Hauteur réelle de Hauteur réelle de la terminaison la terminaison Hauteur minimale de 6,7 m (22 pi); (avec deux coudes) hauteur maximale de 15 m (50 pi) Hauteur maximale de 15 m (50 pi) (tous les systèmes) Hauteur réelle de Hauteur réelle de...
  • Page 35 DOIT ÊTRE EFFECTUÉE PAR DU (1/2 po) de gaz PERSONNEL QUALIFIÉ. Remarque : une hotte FMI PRODUCTS, LLC doit être installée si l'appareil est utilisé avec un ensemble de bûches à gaz sans système Réinstallez d'évacuation (voir Accessoires, page 20).
  • Page 36: Fonctionnement Et Entretien

    FONCTIONNEMENT ET ENTRETIEN PORTES VITRÉES Les portes vitrées sont en option avec ce foyer. Lorsque le foyer fonctionne, les portes vitrées doivent uniquement être complète- ment ouvertes ou complètement fermées; Portes complètement fermées sinon, un risque d'incendie peut exister (voir Façade du foyer figure 23).
  • Page 37: Service Technique

    F M I P R O D U C T S , L L C à l ’ a d r e s s e ou le dépannage. Si c’est le cas, appelez FMI www.fmiproducts.com. PRODUCTS, LLC au 1-866-328-4537. Lors- que vous appelez, veuillez avoir les numéros...
  • Page 38: Pièces

    PIÈCES FOYER À BOIS, MODÈLES (V)B36, (V)B36I, (V)B36L, (V)B36LI www.fmiproducts.com 109034-01H...
  • Page 39 PIÈCES FOYER À BOIS, MODÈLES (V)B36, (V)B36I, (V)B36L, (V)B36LI Cette liste comprend les pièces de rechange utilisées dans votre foyer. Nº Nº DE PIÈCE DESCRIPTION QTÉ Plaque isolante • • Séparateur d'air • • Panneau supérieur de chambre de combustion •...
  • Page 40: Accessoires

    ACCESSOIRES CONDUIT À DOUBLE PAROI 12-8DM 12-8HT 18-8DM 18-8-HT 24-8DM 24-8HT 36-8DM 36-8HT 48-8DM 48-8HT PORTE VITRÉE PLIABLE BDB36 - Noire BDB36B - Laiton brossé BDB36P - Platine SOLINS DE TOITURE INCLINAISON 0 À 6/12 - V6F-8DM INCLINAISON 6/12 À 12/12 - V12F-8DM MITRE SC1-1 pour RT-8DM et RTL-8DM ÉCRAN DE TIRAGE...
  • Page 41 ACCESSOIRES suite PRÊT-À-MONTER DE SOUFFLEUR - BK PRÊT-À-MONTER DE GAINE D'AIR EXTÉRIEUR POUR INSTALLATION AU SOL - AK4F TERMINAISONS À TÊTE RONDE RT-8DM, RTL-8DM, RT-8HT, RLT-8HT TERMINAISON SUPÉRIEURE TERMINAISONS À TÊTE RONDE CARRÉE POUR ENCHÂSSURE AVEC SECTION COULISSANTE ET-8DM, ET-8DM, ET-8HT RTT-8DM, RTTL-8DM, RTT-8HT, RTTL-8HT TERMINAISON SUPÉRIEURE AVEC SECTION COULISSANTE - ETL-8DM,...
  • Page 42 NOTES _____________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ _____________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ _____________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ www.fmiproducts.com 109034-01H...
  • Page 43 NOTES _____________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ _____________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ _____________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ www.fmiproducts.com 109034-01H...
  • Page 44 2701 S. Harbor Blvd. Santa Ana, CA 92704 109034-01 1-866-328-4537 Rev. H www.fmiproducts.com 09/09...

Table of Contents