Table of Contents
Advertisement
Clean discs
Wipe the disc with a micro fi bre cleaning cloth from
the centre to the edge in a straight line movement.
Specifi cations
Note
•
Specifi cation and design are subject to change without notice
USB
•
Compatibility: Hi-Speed USB (2.0)
•
Class support: UMS (USB Mass Storage Class)
Video
•
Signal system: PAL / NTSC
•
Composite video output: 1 Vpp ~ 75 ohm
•
Component video output: 0.7 Vpp ~ 75 ohm
•
HDMI output: 480i, 480p, 576i, 576p, 720p,
1080i, 1080p
Audio
•
Analog stereo output
•
Signal to noise ratio (1 kHz): > 90 dB
(A-weighted)
•
Dynamic Range (1 kHz): > 80 dB (A-weighted)
•
Crosstalk (1 kHz): > 90 dB
•
Distortion/noise: (1 kHz): > 75 dB
•
MPEG MP3: MPEG Audio L3
•
Digital output
•
Coaxial
•
HDMI output
Main unit
•
Dimensions (w x h x d): 360 x 39 x 209 (mm)
•
Net Weight: 1.49 kg
Power
•
Power supply rating: 110-240V, 50/60HZ
•
Power consumption: < 10 W
•
Power consumption in standby mode: < 0.1 W
Accessories supplied
•
Remote control and batteries
•
Audio/Video cables
•
AC power cord
•
User Manual
•
Quick Start Guide
Laser specifi cation
•
Type: Semiconductor laser InGaAIP (DVD),
AIGaAs (CD)
•
Wave length: 655 nm (DVD), 790 nm (CD)
•
Output Power: 7.0 mW (DVD), 10.0 mW
(VCD/CD)
•
Beam divergence: 60 degrees
9 Troubleshooting
Warning
•
Risk of electric shock. Never remove the casing of the product.
To keep the warranty valid, never try to repair the
product yourself.
If you have problems using this product, check the
following points before you request service. If you
still have a problem, register your product and get
support at www.philips.com/welcome.
If you contact Philips, you will be asked for the model
and serial number of your product. The model
number and serial number are on the back of your
product. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Main unit
The buttons on this unit do not work.
•
Disconnect this product from the power
outlet for a few minutes, then connect again.
No reaction to the remote control.
•
Connect this product to the power outlet.
•
Point the remote control at the IR sensor
located on the front panel of this product.
•
Insert the batteries correctly.
•
Insert new batteries in the remote control.
Picture
No picture.
•
See the TVs user manual on how to select
the correct input on the TV. Change the TV
channel until you see the Philips screen.
•
If you have turned on the progressive scan
setting or change the TV system setting,
switch back to default mode: 1) Press
open the disc compartment. 2) Press the
Numeric button '1' (for progressive scan) or
the Numeric button'3' (for TV system).
No picture on HDMI connection.
•
If this product is connected to an unauthorized
display device with an HDMI cable, the audio/
video signal may not be output.
•
Check if the HDMI cable is faulty. Replace a
new HDMI cable.
•
If this happens when you change the HDMI
video resolution, you have to switch to its
default mode: 1) Press
compartment. 2) Press the numeric button "1".
Sound
No audio output from the TV.
•
Ensure that the audio cables are connected to
the audio input of the TV.
•
Assign the audio input of the TV to the
corresponding video input. See the TV user
manual for details.
No audio output from the loudspeakers of the
audio device (stereo system/amplifi er/receiver).
•
Ensure that the audio cables are connected to
the audio input of the audio device.
•
Turn on the audio device to its correct audio
input source.
to
to open the disc
EN
19
Advertisement
Table of Contents
