Black & Decker BDS1616R Original Instructions Manual page 5

Delta cleaning pads :- (cat no. FSMP30-XJ).
Place a cleaning pad (6) on the floor with the velcro 'loop'
u
side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(6).
Caution: Always place your steam mop with the handle (4)
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
Removing a cleaning pad
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (4) to the upright position and turn the
u
steam mop 'OFF'.
Wait until the steam mop cools down (approximately 5
u
minutes).
Lift the steam mop away from the cleaning pad freeing it
u
from the velcro fastening.
Caution! Always place your steam mop with the handle (4)
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
The Delta Head (Fig. D)
This Steam Mop incorporates a built in delta head which
enables you to access into tight corners and narrow gaps.
Caution! Always wear suitable shoes when accessing the
delta head on your steam mop. Do not wear slippers or open
toed footwear.
Return the handle (4) to the upright position and turn the
u
steam mop 'OFF'.
Wait until it cools down (approximately five minutes).
u
Place the front of your shoe onto the steam head removal
u
tab (5b) and press down gently.
Lift the delta head (5a) up off the steam head (5).
u
Fit the delta head cleaning pad (6a) to the bottom of the
u
delta head.
Filling the water tank (Fig. E)
The water tank on your steam mop is removable for
convenient and easy filling.
Note! Fill the water tank with clean tap water.
Note! In areas of hard water, the use of de-ionised water is
recommended.
Remove the water tank (3).
u
Remove the filter cap by unscrewing in an anti-clockwise
u
direction.
Fill the water tank (3) with water.
u
Warning! Your water tank has a 350ml capacity. Do not over
fill the tank.
Replace the filter cap by screwing in a clockwise direction.
u
Re-fit the water tank (3).
u
(Original instructions)
Note! Ensure the filter cap is firmly secured.
Note! Do not use chemical cleaners with your steam mop
water tank.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pad fitted and a continuous run time
of 90 seconds.
Switching on and off
To switch the appliance on, press the ON/Off button (1).
u
It takes approximately 15 seconds for the steam mop to
heat up.
Press the steam operation button (2). This will operate the
u
pump and the unit will begin to produce steam.
To stop steam generation, turn the steam operation button
u
(2) to off. This will maintain power to the boiler for quicker
start up.
To switch the appliance off, press the ON/Off button (1).
u
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (4) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Caution! Always empty the steam mop after use.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
Variable Steam operation
The unit is equipped with a variable steam operation
controlled by the thumb wheel (10) located on the handle grip
(9). This allows for 3 different surface settings.
The variable steam settings are:
Hints for optimum use
General
Caution: Never use the steam mop without first attaching a
cleaning pad.
ENGLISH
Wood / Laminate
Tile / Vinyl
Stone / Marble
5