Advertisement
● 0104: Isolator
This is an equalizer which cuts the volume greatly, allowing you to add a special effect to the
sound by cutting the volume in varying ranges.
No
Parameter
Value
1
Boost/Cut Low
0–64
Boost/Cut Mid
2
0–64
#1
-60–+4 dB
Boost/Cut High
3
0–64
#2
Anti Phase Low
4
0–1
Off, On
Sw
Anti Phase Low
5
0–127
0–127
Level
Anti Phase Mid
6
0–1
Off, On
Sw
Anti Phase Mid
7
0–127
0–127
Level
8
Low Boost Sw
0–1
Off, On
Low Boost
9
0–127
0–127
Level
10
Level
0–127
0-127
● 0105: Low Boost
Boosts the volume of the lower range, creating powerful lows.
No
Parameter
Value
Boost
1
0–8
50–125 Hz
Frequency #1
2
Boost Gain #2
0–12
0–+12 dB
Wide, Mid,
3
Boost Width
0–2
Narrow
4
Low Gain
0–30
-15– +15 dB
5
High Gain
0–30
-15–+15 dB
6
Level
0–127
0–127
● 0106: High Pass Filter
This is a filter with an extremely sharp slope. The cutoff frequency can be varied cyclically.
No
Parameter
Value
Lpf, Bpf, Hpf,
1
Filter Type
0–3
Notch
2
Filter Slope
0–2
-12, -24, -36 dB
3
Filter Cutoff #1
0–127
0–127
Filter
4
0–100
0–100
Resonance #2
5
Filter Gain
0–12
0–+12 dB
6
Modulation Sw
0–1
Off, On
Modulation
Tri, Sqr, Sin,
7
0–4
Wave
Saw1, Saw2
Description
These boost and cut each of the High,
Middle, and Low frequency ranges.
At -60 dB, the sound becomes
inaudible. 0 dB is equivalent to the
input level of the sound.
Turns the Anti-Phase function on and
off for the Low frequency ranges.
When turned on, the counter-channel
of stereo sound is inverted and added
to the signal.
Adjusts the level settings for the Low
frequency ranges.
Adjusting this level for certain
frequencies allows you to lend
emphasis to specific parts. (This is
effective only for stereo source.)
Settings of the Anti-Phase function for
the Middle frequency ranges
The parameters are the same as for the
Low frequency ranges.
Turns Low Booster on/off.
This emphasizes the bottom to create a
heavy bass sound.
Increasing this value gives you a
heavier low end.
Depending on the Isolator and filter
settings this effect may be hard to
distinguish.
Output Level
Description
Center frequency at which the lower
range will be boosted
Amount by which the lower range will
be boosted
Width of the lower range that will be
boosted
Gain of the low frequency range
Gain of the high frequency range
Output level
Description
Filter type
Frequency range that will pass through
each filter
Lpf: Frequencies below the cutoff
Bpf: Frequencies in the region of the
cutoff
Hpf: Frequencies above the cutoff
Notch: Frequencies other than the
region of the cutoff
Amount of attenuation per octave
-36 dB: Extremely steep
-24 dB: Steep
-12 dB: Gentle
Cutoff frequency of the filter
Increasing this value will raise the
cutoff frequency.
Filter resonance level
Increasing this value will emphasize
the region near the cutoff frequency.
Amount of boost for the filter output
On/off switch for cyclic change
How the cutoff frequency will be
modulated
Tri: Triangle wave
Sqr: Square wave
Sin: Sine wave
Saw1: Sawtooth wave (upward)
Saw2: Sawtooth wave (downward)
No
Parameter
Value
8
Rate Mode
0–1
Hz, note
9
Rate
1–127
0.05–10.00 Hz
10
Rate
0–21
note
11
Depth
0–127
0–127
12
Attack
0–127
0–127
13
Level
0–127
0–127
● 0110: Overdrive
Creates a soft distortion similar to that produced by vacuum tube amplifiers.
No
Parameter
Value
1
Drive
0–127
0–127
Small,
Built-In,
2
Amp Type #1
0–3
2-Stack,
3-Stack
3
Low Gain
0–30
-15–+15 dB
4
High Gain
0–30
-15–+15 dB
5
Pan
0–127
L64–63R
6
Level #2
0–127
0–127
● 0111: Distortion
Produces a more intense distortion than Overdrive. The parameters are the same as for
"Overdrive."
● 0112: Overdrive2
This is an overdrive that provides heavy distortion.
No
Parameter
Value
1
Drive
0–127
0–127
2
Tone
0–127
0–127
3
Amp Sw
0–1
Off, On
Small,
Built-In,
4
Amp Type #1
0–3
2-Stack,
3-Stack
5
Low Gain
0–30
-15–+15 dB
6
High Gain
0–30
-15–+15 dB
7
Pan
0–127
L64–63R
8
Level #2
0–127
0–127
● 0113: Distortion2
This is a distortion effect that provides heavy distortion. The parameters are the same as for
"Overdrive2."
MIDI Implementation
Description
When this is set to "note," the effect is
synchronized with the tempo.
Rate of modulation (Hz)
Rate of modulation (note)
Depth of modulation
Speed at which the cutoff frequency
will change
This is effective if Modulation Wave is
SQR, SAW1, or SAW2.
Output level
Description
Degree of distortion
Also changes the volume.
Type of guitar amp
Small: small amp
Built-In: single-unit type amp
2-Stack: large double stack amp
3-Stack: large triple stack amp
Gain of the low range
Gain of the high range
Stereo location of the output sound
Output Level
Description
Degree of distortion
Also changes the volume.
Sound quality of the Overdrive effect
Turns the Amp Simulator on/off.
Type of guitar amp
Small: small amp
Built-In: single-unit type amp
2-Stack: large double stack amp
3-Stack: large triple stack amp
Gain of the low range
Gain of the high range
Stereo location of the output sound
Output Level
17
Advertisement
