Hoshizaki KMD-210AB-HC Instruction Manual page 5

ENGLISH
6) Route the bin control lead through the hole in the base, then into
the bushing provided. See Fig. 5.
Bushing
Bushing
7) While pulling up the bin control lead, hook the bin control on the right
side interior wall. Then push the bin control up against the bottom of
the unit, and slide to the back until it snaps in place. Make sure the
slotted holes at the right side of the bin control are securely placed
on the collars at the bottom of the unit. See Fig. 6.
CAUTION
Make sure the bin control is securely in place. Otherwise, ice may
get between gaps and damage the bin control.
8) Pull up any slack in the bin control lead, then put the bushing attached
to the bin control lead back into the hole in the base.
9) Connect the bin control connector to the side of the control box.
10) Replace the water tank, cube guide, pump motor bracket, pump
motor and float switch in their correct positions. The pump
motor bracket must be attached securely to the back so that the
thumbscrews can be tightened.
CAUTION
Be sure to let the discharge hose pass behind the copper tube
and connect it securely in position. See Fig. 3. Otherwise, the
discharge hose may be caught in the front insulation, leading to
improper results.
Bin Control Lead
Fig. 5
Collars
Bin Control
Fig. 6
11) Secure the pump motor bracket with the two thumbscrews.
12) Reconnect the pump motor connector and float switch connector.
13) Replace the front insulation and front panel in their correct positions.
5. ELECTRICAL CONNECTIONS
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national and local
electrical code requirements. To prevent possible severe electrical
shock to individuals or extensive damage to equipment, install a
proper earth wire to the icemaker. Remove the plug from the mains
socket before any maintenance, repairs or cleaning is undertaken.
* This appliance requires a separate 220 - 240VAC, 10A supply. The
electrical supply must be protected by a suitable circuit breaker.
* The main control box fuse is rated at 5A, 250V and should only be
replaced by a qualified service engineer.
* Usually an electrical permit and services of a licensed electrician are
required.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the
following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
The wire which is coloured Green-and-Yellow must be connected to
the terminal in the plug which is marked with the letter E or by the
symbol or coloured Green or Green-and-Yellow. The wire which
is coloured Blue must be connected to the terminal which is marked
with the letter N or coloured Black. The wire which is coloured Brown
must be connected to the terminal which is marked with the letter L
or coloured Red.
* Should the socket outlets in the installation site not be suitable for the
plug supplied with your product, the plug must be removed (cut off if
it is moulded on plug) and an appropriate plug fitted.
If the non-rewirable plug has been cut from the power supply cord, it
must be disposed of. There should be no attempt to reuse it. Inserting
such a plug into a socket elsewhere presents a serious risk of electrical
shock.
* The non-rewirable plug must never be used without a fuse cover being
fitted.
The correct replacement for the detachable fuse cover is identifiable
from the manufacturer's reference number stamped on the plug.
Supply of replacement fuse covers can be obtained from Hoshizaki
Parts/Service Centres.
Fuses should be rated at 10A and approved to BS 1362.
6. WATER SUPPLY AND DRAIN CONNECTIONS
Connect to potable water supply only.
* The connections to the mains water supply must be made in
accordance with the countries' current requirements of the Water
Supply or Water Fittings Regulations.
4
WARNING
WARNING