Table of Contents
Advertisement
4
Reinstall the anvil holder assembly onto the hand tool
and tighten the attaching cap screw.
5
Crimp a terminal to the proper size wire and check the
wire barrel crimp height of the crimped terminal. If
crimp height is not as specified, remove the anvil
holder assembly and turn the adjusting collar an
additional 5 degrees. Then reinstall the anvil holder
assembly and again check the crimp height. Continue
adjusting the crimp height in this manner until the
proper crimp height is achieved.
6
Remove the anvil holder assembly and tighten the
setscrew clockwise in the adjustable tool holder. Then
reinstall the anvil holder assembly and tighten the
attaching cap screw.
VI. PARTS
A. Spare Parts
These are parts that FCI Electronics considers practical for the
user to stock for replacement. Recommended spare parts for the
hand tool are specified in bold type in the parts list for Figure
13.
Index
Part No.
no.
1
A-857-5
2*
104964-1
3*
108175-1
4*
108176-1
5
A-1153
6
A-1155
7
915305-224
8
104963-1
9
915305-205
10
915305-559
11
102466-1
12*
108178-1
13*
108178-2
14*
108177-1
15*
108177-2
16
102470-1
17
147070-1
18
900066-001
19
102468-2
20
144547-001
21
147071-1
22
147072-1
23
102470-2
24
150564-1
*Recommended Spare Parts
FCI Electronics
Issued: Date (10/24/94)
Rev. 03/08/01 ECR V103118
K\DCU\Manuals
ELECTRONICS
Parts List for Figure 13, HT-0102 Hand Tool Parts
Description
CRIMPER HOLDER
TONKER
INSULATION BARREL CRIMPER 22-32 GAUGE WIRE
WIRE BARREL CRIMPER 22-32 GAUGE WIRE
TONKER SPRING
GUIDE SPRING
⅜
SHCS, 4-40 NF X
" LONG
SPRING RETAINER
½
SHCS, 6-40 NF X
" LONG
SHSS(SET SCREW) 2-56 NC X 1/8" LONG
ANVIL HOLDER
INSULATION BARREL ANVIL, SIDE "A", 28-32 G WIRE
INSULATION BARREL ANVIL, SIDE "B", 22-26 G WIRE
WIRE BARREL ANVIL, SIDE "A", 28-32 G WIRE
WIRE BARREL ANVIL, SIDE "B", 22-26 G WIRE
TERMINAL HOLDER SPRING, 0.65" LONG
TERMINAL HOLDER
O-RING, 0.070" I.D., 01-004
GUIDE PIN
GUIDE RAIL
TERMINAL CLAMP
QUILL PUNCH
PUNCH SPRING, 0.300" LONG
@,
COLLAR. NYLON
PRESS-FIT, 0.0625" I.D.
PDM: Rev:B
B. Parts Ordering Information
To obtain replacement parts, contact FCI Electronics, 825
Old Trail Road, Etters, PA 17319; Phone Toll Free 1-800-
237-2374. Provide the description of the part, FCI part
number (if specified), quantity desired, and also the hand
tool model and serial number.
C. Hand Tool Repair Policy
FCI Electronics charges a standard rate to repair any hand
tool not under warranty. Phone Toll Free 1-800-237-2374
to obtain a Return Material Authorization number (RMA),
shipping instructions and the current cost of repair. FCI will
repair the hand tool and return it to you by the fastest means
possible.
Manual Part No. 144000-001
Page 9 of 10
Revision B
Released
STATUS:
Quantity
1
2
1
1
2
2
8
1
2
2
1
1
1
1
1
2
1
2
2
2
1
1
1
1
Printed: Dec 20, 2002
Advertisement
Table of Contents
