Table of Contents
Advertisement
Quick Links
Table of Contents ............................1
Usage Notice ...................................2
Safety Information ...............................2
Precautions .........................................3
Eye Safety Warnings ..........................5
Product Features ................................5
Introduction ......................................6
Package Overview ..............................6
Product Overview ...............................7
Main Unit .............................................. 7
Control Panel ....................................... 8
Input/Output Connections .................... 9
Remote Control .................................. 10
Installation ..................................... 11
Connecting the Projector ..................11
Connect to Computer/Notebook ........ 11
Connect to Video Sources ................. 12
Powering the Projector On / Off ........13
Powering On the Projector ................. 13
Powering off the projector .................. 14
Warning Indicator ............................... 14
Adjusting the Projected Image ..........15
Adjusting the Projector's Height ........ 15
Focus ................................................. 16
Adjusting Projection Image Size ........ 17
User Controls ................................20
Control Panel ..................................... 20
Remote Control .................................. 21
On-screen Display Menus ................28
How to operate .................................. 28
Menu Tree .......................................... 29
IMAGE ............................................... 31
IMAGE | Advanced ............................ 33
DISPLAY ............................................ 36
DISPLAY | 3D ................................... 39
SETUP ............................................... 40
SETUP | Security ............................... 42
Table of Contents
SETUP | Audio Settings ..................... 44
SETUP | LAN Settings ....................... 45
SETUP | Advanced ............................ 47
OPTIONS ........................................... 48
OPTIONS | Remote Settings ............. 50
OPTIONS | Advanced ........................ 51
OPTIONS | Lamp Settings ................. 52
Appendices ....................................54
Troubleshooting ................................54
Replacing the Lamp ..........................60
Installing and Cleaning the Filter ......62
Compatibility Modes .........................63
Compatibility ...................................... 63
3D Input Video Compatibility ............. 64
Function List .....................................65
RS232 Pin Assignments .................... 65
RS232 Protocol Function List ............ 66
Ceiling Mount Installation ..................70
Optoma Global Offices .....................71
Regulation & Safety Notices .............73
1
English
Advertisement
Table of Contents
Related Manuals for Optoma X351
Summary of Contents for Optoma X351
-
Page 1: Table Of Contents
Powering On the Projector ....13 Ceiling Mount Installation ....70 Powering off the projector ....14 Warning Indicator ....... 14 Optoma Global Offices .....71 Adjusting the Projected Image ..15 Regulation & Safety Notices .....73 Adjusting the Projector’s Height ..15 Adjusting the Projector’s Zoom /... -
Page 2: Usage Notice
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Optoma before you send the unit for repair. 7. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could result in fire or electric shock. -
Page 3: Precautions
Usage Notice Precautions Please follow all warnings, precautions and maintenance as recommended in this user’s guide. ▀■ Warning- Do not look into the projector’s lens when the lamp is on. The bright light may hurt and damage your eyes. ▀■ Warning- To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture. - Page 4 Usage Notice Turn off and unplug the power plug from the AC outlet before cleaning the product. Use a soft dry cloth with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is ...
-
Page 5: Eye Safety Warnings
Usage Notice Eye Safety Warnings ▀■ Avoid staring/facing directly into the projector beam at all times. Keep your back to the beam as much as possible. ▀■ When projector is used in a classroom, adequately supervise students when they are asked to point out something on the screen. -
Page 6: Introduction
Introduction Package Overview Unpack and inspect the box contents to ensure all parts listed below are in the box. If something is missing, please contact your nearest customer service center. Projector Power Cord VGA Cable Power Switch Freeze Enter Page Laser Page+ Keystone... -
Page 7: Product Overview
Introduction Product Overview Main Unit Standard Short Throw Focus Ring Focus Ring Zoom Lever IR Receiver The interface IR Receiver Control Panel is subject to Control Panel Input / Output Connec- model’s specifi- cations. Input / Output Connec- tions Do not block tions Kensington Lock Port... -
Page 8: Control Panel
Introduction Control Panel Source Keystone Correction Enter Re-Sync Help Four Directional Select Keys Temp LED Power On/Standby LED Lamp LED Menu English... -
Page 9: Input/Output Connections
VGA dongle is a Audio2 Input Connector (3.5mm mini jack) optional accesso- Audio Output Connector (3.5mm mini jack) ry. Please contact Optoma service Audio1 Input Connector (3.5mm mini jack) for details. RS-232 Connector (9-pin) USB service and remote mouse Power RJ45... -
Page 10: Remote Control
Introduction Remote Control The interface is Power Switch Power On/Off subject to model’s specifications. Freeze Display Blank & Audio Freeze Mute USB Mouse Left Click Enter Left Selection Key Enter Laser Pointer Trigger Page Down Keystone +/- Page Laser Page+ Aspect Keystone Volume... -
Page 11: Installation
Installation Connecting the Projector Connect to Computer/Notebook Monitor Output Audio Output Due to the difference in applications for each country, some regions may molex have different accessories. (*) Optional accessory The interface is subject to model’s specifications . 1..................*Audio Output Cable 2.....................*VGA Out Cable 3.....................VGA Cable 4....................*HDMI Cable... -
Page 12: Connect To Video Sources
Installation Connect to Video Sources Composite Video Output DVD Player, Set-top Box, S-Video Output HDTV receiver Due to the difference in applications for each country, some regions may have different accessories. (*) Optional accessory DVD Player, Set-top Box, HDTV receiver The interface is Audio Output subject to model’s... -
Page 13: Powering The Projector On / Off
Installation Powering the Projector On / Off Powering On the Projector 1. Securely connect the power cord and signal cable. When connected, the POWER LED will turn red. 2. Turn on the lamp by pressing “ ” button either on the top of When Power mode ... -
Page 14: Powering Off The Projector
Installation Powering off the projector 1. Press the “ ” button on the remote control or on the control panel to turn off the projector. The following message will be displayed on the screen. Press the “ ” button again to confirm otherwise the message will disappear after 15 seconds. -
Page 15: Adjusting The Projected Image
Installation Adjusting the Projected Image Adjusting the Projector’s Height The projector is equipped with elevator feet for adjusting the image height. 1. Locate the adjustable foot you wish to modify on the underside of the projector. 2. Rotate the adjustable ring clockwise to raise the projector or counter clockwise to lower it. -
Page 16: Adjusting The Projector's Zoom / Focus
Installation Adjusting the Projector’s Zoom / Focus You may turn the zoom ring to zoom in or out. To focus the im- age, rotate the focus ring until the image is clear. XGA series: The projector will focus at distances from 3.28 to 39.4 feet (1.0 to 12.0 meters). -
Page 17: Adjusting Projection Image Size
Installation Adjusting Projection Image Size XGA series: Projection Image Size from 27.5”~ 302.8” (0.70 to 7.69 meters). WXGA series: Projection Image Size from 27.3” to 299.5” (0.69 to 7.60 meters). XGA with 0.6 TR: Projection Image Size from 60.7”~291.7”, up to 300”... - Page 18 Installation Standard Screen Size W x H Projection Distance (D) Diagonal length Offset (Hd) (inch) size of (inch) (feet) 4:3 Screen Width Height Width Height wide tele wide tele (inch) 30.00 0.61 0.46 24.00 18.00 1.19 1.31 3.90 4.30 0.07 2.70 40.00 0.81...
- Page 19 Installation Short Throw Screen Size W x H Projection Distance (D) Diagonal length Offset (Hd) (inch) size of (inch) (feet) 4:3 Screen Width Height Width Height wide tele wide tele (inch) 32.00 0.65 0.49 25.59 19.29 0.40 0.40 1.31 1.31 0.07 2.89 40.00...
-
Page 20: User Controls
User Controls Control Panel & Remote Control Control Panel Using the Control Panel Refer to the “Power On/Off the Projector” section on POWER pages 13-14. Automatically synchronize the projector to the input RE-SYNC source. ENTER Confirm your item selection. SOURCE Press “SOURCE”... -
Page 21: Remote Control
User Controls Remote Control Using the Remote Control Refer to the “Power On/Off the Projector” Power section on pages 13-14. Power Switch Switch USB mouse switch. Display blank Momentarily turns off/on the audio and Freeze & Audio mute video. Freeze Temporarily freeze the video. - Page 22 User Controls Using the Remote Control HDMI Press “HDMI” to choose HDMI source. Press “VGA” to choose VGA sources. Press “Video” to choose Composite Video Video and S-video source. User defined keys Keys can be defined in projector OSD. (1/2/3) Source Press “Source”...
- Page 23 User Controls NEC_CODE repeat custom code Data position legend format Byte 1 Byte 2 Byte 3 Byte 4 Power Switch Display blank&Audio mute Freeze Mute LEFT Enter C5/CA 3A/35 Right ...
- Page 24 User Controls Installing Batteries Replace only with the same or equivalent type recommend- ed by the manufacturer. CAUTION Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below. • Do not mix batteries of different types. Different types of batteries have different characteristics.
- Page 25 User Controls Using the HELP button The HELP function ensures easy setup and operation. Press the “?” button on the control panel to open the Help Menu. English...
- Page 26 User Controls Help menu button functions only when no input source is detected. Please refer to the “Troubleshooting” section on pages 54-59 for more details. If input source is detected and help button is pressed, the following pages will appear to help diagnose any problems. English...
- Page 27 User Controls English...
-
Page 28: On-Screen Display Menus
User Controls On-screen Display Menus The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a variety of settings. How to operate To open the OSD menu, press “Menu” on the Remote Control or Projector Keypad. -
Page 29: Menu Tree
User Controls Menu Tree Settings Main Menu Sub Menu IMAGE Display Mode Presentation / Bright / Movie / sRGB / Blackboard / User / 3D Brightness -50~50 Contrast -50~50 Sharpness 1~15 Color -50~50 Tint -50~50 Advanced Gamma Film / Video / Graphics / Standard BrilliantColor™... - Page 30 User Controls Settings Main Menu Sub Menu Projector ID 0~99 SETUP Audio Settings Internal Speaker On / Off Mute On / Off Volume 0~10 Audio Input Default / AUDIO1 / AUDIO2 Audio Input 2 function Mic / Audio Input2 Network Status Connect/Disconnect(Read-Only) LAN Settings DHCP...
-
Page 31: Image
User Controls IMAGE Display Mode There are many factory presets optimized for various types of images. Presentation: Good color and brightness from PC input. Bright: Maximum brightness from PC input. Movie: For home theater. sRGB: Standardised accurate color. ... - Page 32 User Controls Sharpness Adjust the sharpness of the image. Press the to decrease the sharpness. Press the to increase the sharpness. Color Adjust a video image from black and white to fully saturated color. “Color” and “Tint” Press the to decrease the amount of saturation in the image.
-
Page 33: Image | Advanced
User Controls IMAGE | Advanced Gamma This allows you to choose a degamma table that has been fine-tuned to bring out the best image quality for the input. Film: for home theater. Video: for video or TV source. Graphics: for image source. - Page 34 User Controls Red/Green/Blue/Cyan/Magenta/Yellow: Use to select Hue, Saturation and Gain Colors. White: Use to select Red, Green and Blue Colors. Reset: Choose “Yes” to return the factory default settings for color adjustments. Color Space Only available while HDMI input Select an appropriate color matrix type from AUTO, RGB, RGB source is connect-...
-
Page 35: Image | Advanced | Signal (Rgb)
User Controls IMAGE | Advanced | Signal (RGB) Automatic “Signal” is only supported in Analog Automatically selects the signal. If you use this function, the VGA (RGB) signal. Phase, frequency items are grayed out, and if Signal is not auto- matic, the phase, frequency items will appear for user to manually tune and saved in settings after that for next time projector turns off and on again. -
Page 36: Display
User Controls DISPLAY Format Use this function to choose your desired aspect ratio. 4:3: This format is for 4×3 input sources. 16:9: This format is for 16×9 input sources, like HDTV and DVD enhanced for Wide screen TV. Native: This format displays the original image without any ... - Page 37 User Controls Aspect ratio Resize image (SVGA) Resize image (XGA) (source detected) 800 x 600 center 1024 x 768 center 16:9 800 x 450 center 1024 x 576 center No resize image, 1:1 mapping and Native centered. This format shows the original image without scaling.
- Page 38 User Controls 16:10 Screen 480i/p 576i/p 1080i/p 720p 1066 x 800 center 16:10 1280 x 800 center 1:1 map- 1:1 mapping ping (960 x 1280 x 720 Native mapping centered. 540) display center centered. 1280 x 800 16:9 Screen 480i/p 576i/p 1080i/p 720p...
-
Page 39: Display | 3D
User Controls DISPLAY | 3D 3D Mode Off: Select “Off” to turn 3D settings off for 3D images. DLP Link: Select “DLP Link” to use optimized settings for DLP Link 3D images. “3D Sync Invert” is 3D -> 2D only available when 3D is enabled and 3D: Display 3D signal. -
Page 40: Setup
User Controls SETUP Language Choose the multilingual OSD menu. Press into the sub menu and then use the key to select your preferred language. Press “Enter” to finalize the selection. Projection Front-Desktop Rear-Desktop and This is the default selection. The image is projected straight on Rear-Ceiling are the screen. - Page 41 User Controls Menu Location Choose the menu location on the display screen. Screen Type Choose the screen type from16:10 or 16:9. “Screen Type” is for WXGA only. Projector ID ID definition can be set up by menu (range 0-99), and allow user control an individual projector by RS232.
-
Page 42: Setup | Security
User Controls SETUP | Security “Security” depends on model’s specifi- cations. Security On: Choose “On” to use security verification when turning on the projector. Off: Choose “Off” to be able to switch on the projector without password verification. Security Timer Use this function to set how long (Month/Day/Hour) the projector can be used. - Page 43 User Controls If the incorrect password is entered 3 times, the projector will automatically shut down. If you have forgotten your password, please contact your local office for support. English...
-
Page 44: Setup | Audio Settings
User Controls SETUP | Audio Settings Internal Speaker Choose the “On” or “Off” to turn on or off the internal speaker. Mute Choose the “On” to turn mute on. Choose the “Off” to turn mute off. Audio input2 Function Mic: Use Microphone as secondary audio input. -
Page 45: Setup | Lan Settings
User Controls SETUP | LAN Settings Network State Choose “Connect” to enable LAN network function. Choose “Disconnect” to disable LAN network function. (Read- Only mode) DHCP If a DHCP server exists in the network to which the projector is connected, the IP address will automatically be acquired when you select DHCP On. - Page 46 User Controls Check the DNS Server IP address with your network/system administrator if you wish to configure it manually. Default value is 192.168.0.51. Apply Choose “Yes” to save the changes made in network configuration settings. MAC Address Display MAC addresss for the projector. English...
-
Page 47: Setup | Advanced
User Controls SETUP | Advanced Logo Press to capture an image of the picture currently displayed on screen. If changes are made they will take effect the next time the projector is powered on. Default: The default startup screen. Neutral: Logo is not displayed on startup screen. -
Page 48: Options
User Controls OPTIONS Input Source Use this option to enable / disable input sources. Press to enter the sub menu and select which sources you require. Press “Enter” to finalize the selection. The projector will not search for inputs that are not selected. - Page 49 User Controls IR Function On: Choose “On”, the projector can be operated by the remote control. When you change the setting from “Off” to “On”, it will display a warning message: (*) The function de- pends on model’s specifications. Off: Choose “Off”, you will only be able to use the control panel ...
-
Page 50: Options | Remote Settings
User Controls OPTIONS | Remote Settings The function of User 1/2/3 keys on the remote control can be self- defined. You can choose a desired function for these keys separately in this option. User 1 The available options for User1 key are VGA2/S-Video/LAN/Bright- ness/Contrast/Sleep Timer. -
Page 51: Options | Advanced
User Controls OPTIONS | Advanced Direct Power On Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied, without pressing the “ ” key on the projector control panel or on the remote control. -
Page 52: Options | Lamp Settings
User Controls OPTIONS | Lamp Settings Lamp Hours Display the projection time. Lamp Reminder Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will appear 30 hours before suggested replacement of lamp. -
Page 53: Options | Optional Filter Settings
User Controls OPTIONS | Optional Filter Settings Optional Filter Installed Select “Yes” to display warning message after 500 hours of use. Select “No” to turn off warning message. The default setting for Filter is “No”. After assembling filter, please turn on the projector then press “Menu”, go to “OPTIONS -> Op- tional Filter Settings ->... -
Page 54: Appendices
Appendices Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. No image appears on-screen Ensure all the cables and power connections are correctly and ... - Page 55 Appendices 7. Click on “Show all devices”. Next, select “Standard monitor types” under the SP box; choose the resolution mode you need under the “Models” box. 8. Verify that the resolution setting of the monitor display is lower than or equal to UXGA (1600 × 1200). If you are using a Notebook: ...
- Page 56 Appendices Image has vertical flickering bar Use “Frequency” to make an adjustment. See page 35 for more information. Check and re-configure the display mode of your graphic card to make it compatible with the projector. Image is out of focus Adjust the Focus Ring on the projector lens.
- Page 57 Appendices Image is reversed Select “SETUP Projection” from the OSD and adjust the projection direction. The projector stops responding to all controls If possible, turn off the projector, then unplug the power cord and wait at least 60 seconds before reconnecting power. Check that “Keypad Lock”...
- Page 58 Appendices LED lighting message ON/STANDBY Message Temp-LED Lamp-LED (Blue/Red) (Red) (Red) Standby State (Input power cord) Flashing Power on (Warming) Blue Lamp lighting Blue Flashing Power off (Cooling) Blue Flashing Error (Over Temp.) Steady light Flashing No light Error (Fan fail) Flashing Flashing...
- Page 59 Appendices On Screen Messages Temperature warning: Fan failed: Lamp warning: Out of display range: If the remote control does not work Check the operating angle of the remote control is within ±20° both horizontally and vertically of one of the IR receivers on the projector.
-
Page 60: Replacing The Lamp
Appendices Replacing the Lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp. - Page 61 Appendices The screws on the lamp cover and the lamp cannot be removed. The projector cannot be turned on if the lamp cover has not been placed back on the projector. Do not touch the glass area of the lamp.
-
Page 62: Installing And Cleaning The Filter
Appendices Installing and Cleaning the Filter Installing the Filter Install two filters. Turn on the projector then press “Menu”, go to “OPTIONS -> Optional Filter Settings -> Optional Filter Installed” and select “Yes”. Dust filters are only required/sup- plied in selected regions with ex- cessive dust. -
Page 63: Compatibility Modes
Appendices Compatibility Modes Computer/Video/HDMI/Mac Compatibility Refresh Rate Signal Resolution Video Analog HDMI (Hz) NTSC 720 x 480 For widescreen resolution (WXGA), PAL/SECAM 720 x 576 the compatibility 640 x 480 support is depen- 640 x 480 dent on Notebook/ 640 x 480 72.8 PC models. -
Page 64: 3D Input Video Compatibility
Appendices Refresh Rate Signal Resolution Video Analog HDMI (Hz) UXGA 1600 x1200 1920 x 1080 1920 x 1080 HDTV (1080p) 1920 x 1080 1920 x 1080 1920 x 1080 HDTV (1080i) 1920 x 1080 1920 x 1200 (*4) (*4) WUXGA (*1) 1920 x 1200 SDTV (576i) -
Page 65: Rs232 Commands And Protocol Function List
Appendices RS232 Commands and Protocol Function List RS232 Pin Assignments Pin no. Spec. I/O (From Pin no. Name Projector Side) The interface is subject to model’s specifications. English... -
Page 66: Rs232 Protocol Function List
XX=00-99, projector's ID, Baud Rate : 9600 XX=00 is for all projectors Data Bits: 8 Parity: None 1. There is a <CR> after Optoma V1 Command Table. Stop Bits: 1 all ASCII commands. --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Flow Control : None < >... - Page 67 Appendices --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ~XX45 n 7E 30 30 34 34 20 a 0D Color (Saturation) n = -50 (a=2D 35 30) ~ 50 (a=35 30) --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ~XX60 5 7E 30 30 36 30 20 35 0D i t a --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ~XX61 n 7E 30 30 36 31 20 a 0D Edge mask n = 0 (a=30) ~ 10 (a=31 30)
- Page 68 Appendices --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ~XX88 0 7E 30 30 38 38 20 30 0D Closed Captioning ~XX89 0 7E 30 30 38 39 20 30 0D Audio Input Default --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ~XX100 1 7E 30 30 31 30 30 20 31 0D Source Lock i t a ~XX101 1 7E 30 30 31 30 31 20 31 0D...
- Page 69 Appendices READ from projector ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ~XX121 1 7E 30 30 31 32 31 20 31 0D Input Source Commands n: 0/1/2/3/4/5= None/VGA1/VGA2/Video/S-Video/HDMI ~XX122 1 7E 30 30 31 32 32 20 31 0D Sofware Version OKdddd dddd: FW version ~XX123 1 7E 30 30 31 32 33 20 31 0D Display Mode...
-
Page 70: Ceiling Mount Installation
Ceiling Mount Installation 1. To prevent damage to your projector, please use the Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector... -
Page 71: Optoma Global Offices
Appendices Optoma Global Offices For service or support please contact your local office. 3178 Laurelview Ct. 888-289-6786 Fremont, CA 94538, USA 510-897-8601 www.optomausa.com services@optoma.com Canada 3178 Laurelview Ct. 888-289-6786 Fremont, CA 94538, USA 510-897-8601 www.optomausa.com services@optoma.com Latin America 3178 Laurelview Ct. - Page 72 Appendices Deutschland Wiesenstrasse 21 W +49 (0) 211 506 6670 D40549 Düsseldorf, +49 (0) 211 506 66799 Germany info@optoma.de Scandinavia Lerpeveien 25 +47 32 98 89 90 3040 Drammen +47 32 98 89 99 Norway info@optoma.no PO.BOX 9515 3038 Drammen...
-
Page 73: Regulation & Safety Notices
Appendices Regulation & Safety Notices This appendix lists the general notices of your projector. FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. - Page 74 Appendices Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation.