Advertisement
Quick Links
Advertisement
Related Manuals for Acer Veriton M6660G
Summary of Contents for Acer Veriton M6660G
- Page 1 Veriton M6660G (VM6660G) / Veriton M4660G (VM4660G) Recycling Guide...
-
Page 2: Table Of Contents
Disassembly Procedure ………………………………………………………………………………………………………3 Troubleshooting …………………………….………………………………………….………………………………………15 Exploded diagrams ….…………………………………………………………………………………………………………18 FRU (Field Replaceable Unit) List…………………………………………………………………………………………19 To update your software ….………………………………………………………………………………………….…….20 To remove your personal data ……………………………………………………………………………….………….20... -
Page 3: Disassembly Procedure
Disassembly Procedure Safety Guidelines This chapter contains step by step procedures on how to remove and de-install components from the computer. Use the following safety guidelines to ensure your personal safety. Each procedure included in this chapter assumes that you are preparing your computer for recycling and disposal. By performing any of these procedures you acknowledge that any remaining warranty applicable to your computer will be voided. - Page 4 WEEE Annex VII Component These components are classified as requiring selective treatment. Pre-disassembly Instructions Do the following prior to starting any maintenance procedures: 1. Place the system on a stable work surface. 2. Remove AC power cord from the system and peripherals 3.
- Page 5 Chassis Door Removal Remove the two (2) screws from the chassis door Remove the 2 screws Remove the left side cover...
- Page 6 ODD and card reader Module Removal 2. Remove the ODD Disconnect the ODD SATA cables and ODD power-cables from the rear of ODD Remove two screws fixed in ODD cage Remove the ODD...
- Page 7 3. Remove the Card Reader module. Disconnect the CR cable, intrusion cable, INT SPK cable, audio cable, USB cable from the MB INT_SPK F-USB1 F-USB2 Intrusion F_AUDIO Slither the green lock then pull out the Card Reader module Take out the Card Reader module...
- Page 8 HDD Removal 4. Remove HDD Disconnect the SATA cables and SATA power-cables from the rear of MB Disconnect the SATA cables and SATA power-cables from HDD Take out the HDD from HDD cage Rotate the mobile rack then take out the HDD...
- Page 9 5. Remove the system fan 5.1 Remove four screws of system fan 5.2 Remove the connector of system fan from MB...
- Page 10 VGA card Removal Remove VGA Card Remove the screw of VGA Rotate the PCI cover Remove VGA card...
- Page 11 PSU Removal Remove internal PSU 7.1 Remove the four screws fixed in the rear chassis 7.2 Disconnect the power connectors from MB 7.3 Push the latch then take out the PSU...
- Page 12 MotherBoard, MEM, CPU, Cooler, WLAN, SSD, RTC Battery Removal 8. Remove the Main Board 8.1 Disconnect the F_U31C1, F_U31C2 and USB3F1 F_U31C2 F_U31C1 USB3F1 8.2 Disconnect the front panel cable...
- Page 13 8.3 Remove the eight screws from MB NOTE: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows. WEEE Annex VII component 8.4 Release the four latch show bellow then remove the Memory 8.5 Remove the four screws and disconnect the CPU cooler power-cable from the MB...
- Page 14 8.6 Remove the CPU 8.7 Remove the M.2 SSD 8.8 Remove the battery NOTE: RTC battery has been highlighted with the yellow circle as above image shows. WEEE Annex VII component.
-
Page 15: Troubleshooting
Troubleshooting This chapter provides troubleshooting information for the Veriton M6660G/M4660G Service Guide Power-On Self-Test (POST) POST Error Messages List Power-On Self-Test (POST) Each time you turn on the system, the Power-on Self Test (POST) is initiated. Several items are tested during POST, but for the most part transparent to the user. - Page 16 POST Error Messages List If you cannot run the diagnostics program tests but did receive a POST error message, use “POST Error Messages List "to diagnose system problems. If you did not receive any error message, look for a description of your error symptoms in “Error Symptoms List”.
- Page 17 Memory test fail If POST detects an error during memory testing, additional information appears giving specifics about the type and location of the memory error. Override enabled - If the system cannot boot using the current CMOS configuration, the BIOS can override the Defaults loaded current configuration with a set of BIOS defaults designed for the most stable, minimal- performance system operations.
-
Page 18: Exploded Diagrams
Exploded Diagrams Figure 1 System Exploded Diagram... -
Page 19: Fru (Field Replaceable Unit) List
FRU (Field Replaceable Unit) List Please contact your local service center to find out how to obtain the part or replace your device... -
Page 20: To Update Your Software
To update your software Please visit http://go.acer.com/?id=17883 To remove your personal data Option 1: Select Start > Settings > Update & Security > Recovery. Under Reset this PC, select Get started. Open Recovery settings. Option 2: Restart your PC to get to the sign-in screen, then press and hold down the Shift key while you select the Power icon >...