Related Manuals for Oceanic Stauna Controller
Summary of Contents for Oceanic Stauna Controller
- Page 1 S a u n a & S t e a m STAUNA CONTROLLER Assembly and operating manual PRODUCT IMAGE Oceanic Ltd, Pountney Street, Wolverhampton, WV2 4HX Phone: 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk...
-
Page 2: Table Of Contents
Guarantee ..........15 Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 3: Introduction
S a u n a & S t e a m Stauna Manual Introduction Thank you for choosing to buy our Oceanic Stauna Controller please take the time to read these instructions before you begin as they contain important information about the installation and maintenance requirements. - Page 4 C - 40-50% humidity Max Temp 48 C - 50-60% humidity Sauna Tepidarium Very High Heat - No Steam High Heat - Low Steam Max Temp 100 Max Temp 65 C - 30-40% humidity Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk...
-
Page 5: General Setup Overview
OC - ST Temperature Sensor 4 core 12v cable Lighting circuit - 240v (4m Supplied) Blue - 12 volts Switched from button on Keypad Black - 240 volts Mains in 230v 1N or 400v 3N Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 6: Installing The Sauna Heater
Sauna Heater Dimensions 410 x 280 x H570mm Model Sauna Room Clearance Distances (mm) Current (A) Fuse (A) Volume (m Distance to shelf Ceiling Floor 230V 400V 230v 400V height over 500mm OCS45 1900 1100 19.5 OCS60 1900 1100 Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 7: Sauna Heater Parts Description
Supporting Screw 6mm x 40mm (4pcs) Fig. 3b Fig. 3a Note: Securing screws must be fixed through the top holes of the fixing brackets and prevent the heater being lifted off Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 8: Minimum Clearances
Fig. 4 ii. Open the cover with a screwdriver as in Fig. 5 iii. Fix the bottom of the temperature sensor on to wall with screw iv. Replace the cover. 1800 Fig. 5 Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 9: Mini Steam Generator
Dimensions LxWxH (mm) Class 1 Class 2 Class 3 Class 1 Class 2 Class 3 OC-Mini-1 1000 210-240 2.1-2.3 3.2-3.6 4.2-4.8 220 x 100 x 340 7.3. Mini Steam Generator Circuit Diagram Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 10: Parts Description
Securing screws must be fixed through a whole in the brackets at the bottom rear to prevent the unit being lifted off. iv. Connect the steam generator to the stauna control box (see pages 4, 9, 13) Fixing points for 40mm screw Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 11: Minimum Clearance Diagram
A - Tank Full B - Tank half full C - Tank near empty - refill before use Ignore the controls on front of this unit, OC-ST stauna controller will override these functions. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 12: Stauna Control Box
Remarks L x W x H (mm) OC-ST 15-240 30 - 60 150 x 92 x 22 When the time window displays ”Long” the generator will operate continuously until it is switched off. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 13: Stauna Control Circuit Diagram
S a u n a & S t e a m Stauna Manual 8.3. Stauna Control Circuit Diagram This diagram can be found on the back of the control panel’s cover. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 14: Stauna Control Box Circuit Diagram
Indicates the detected temperature is lower than the preset temperature and sauna heater is heating. Indicates the detected temperature is higher than the preset temperature and the sauna heater is idling. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk... -
Page 15: Operation
Push On/Off to switch on the system. iii. The Stauna Controller has 4 different heat settings which can be selected by pushing the ‘MODE’ button, an LED will indicate which mode (“atmosphere”) you have chosen. Each press moves the LED one position from left to right.
Need help?
Do you have a question about the Stauna Controller and is the answer not in the manual?
Questions and answers