Advertisement
REGULATORS
SLIMLINE 2 OCTO SECOND STAGE
OCEANIC
®
SLIMLINE 2 OCTO
SERVICE
PROCEDURE
This SlimLine 2 Service Procedure conveys a list of components and service procedures
that reflect the SlimLine 2 as it was configured at the time of this writing (2/19/05).
Doc. 12-2809-r01 (2/19/05)
PG-1
OCEANIC ® Product Service Guide
©2002 Design, 2005
Advertisement
Table of Contents
Related Manuals for Oceanic SLIMLINE 2 OCTO
Summary of Contents for Oceanic SLIMLINE 2 OCTO
- Page 1 REGULATORS SLIMLINE 2 OCTO SECOND STAGE OCEANIC ® SLIMLINE 2 OCTO SERVICE PROCEDURE This SlimLine 2 Service Procedure conveys a list of components and service procedures that reflect the SlimLine 2 as it was configured at the time of this writing (2/19/05).
-
Page 2: Table Of Contents
REGULATORS SLIMLINE 2 OCTO SECOND STAGE CONTENTS TROUBLESHOOTING ................................. 3 DISASSEMBLY PROCEDURE ..............................4 REASSEMBLY PROCEDURE ..............................5 FINAL TUNING AND TESTING ..............................7 PARTS LIST AND EXPLODED VIEW DIAGRAM ........................10 GENERAL PROCEDURES REFER TO ................................DOC. 12-2202 SPECIFICATIONS... -
Page 3: Troubleshooting
REGULATORS SLIMLINE 2 OCTO SECOND STAGE TROUBLE SHOOTING SYMPTOM POSSIBLE CAUSE TREATMENT * Free flow or leakage present. 1. Excessive LEVER ARM (9) height. 1. Adjust ORIFICE (2) and LOCK 2. Excessive Intermediate Pressure NUT (12) to arrive at correct from First Stage. -
Page 4: Disassembly Procedure
REGULATORS SLIMLINE 2 OCTO SECOND STAGE DISASSEMBLY PROCEDURE NOTE: Be sure to perform the steps outlined in the Initial Inspection Procedures Doc 12-2022 prior to disassembling the Regulator. Review the Troubleshooting Section to gain a better idea of which internal Parts may be worn, and to better advise your customer of the service that is needed. -
Page 5: Reassembly Procedure
WARNING: Use only genuine Oceanic Parts, Subassem- blies, and Components whenever Assembling Oceanic prod- ucts. DO NOT attempt to substitute an Oceanic Part with another manufacturer’s, regardless of any similarity in shape, size, or appearance. Doing so may render the product unsafe, and could result in serious injury or death of the user. - Page 6 REGULATORS SLIMLINE 2 OCTO SECOND STAGE 4. Apply a light film of lubricant to each end of the POPPET SPRING (7) and place onto the POPPET (6). Fit the POPPET into the Pronged end of the Poppet Tool and insert the Shaft of the POPPET...
-
Page 7: Final Tuning And Testing
13. Place the FRONT COVER RING (16) down over the FRONT COVER (17) and hand tighten clockwise until secure and in proper alignment, attained when the Oceanic logo faces the MOUTH- PIECE (18) (Fig. 13). Use the Front Cover Tool, if necessary. DO NOT overtighten. - Page 8 REGULATORS SLIMLINE 2 OCTO SECOND STAGE 4. Slowly open the valve to pressurize the Regulator, and check the Test Gauge to ensure that the Intermediate Pressure is set as recommended in the Specifications for the First Stage used. NOTE: If the Intermediate Pressure is found to be other than recommended, refer to that Regulator's Trouble Shooting Section to determine possible cause and treatment.
- Page 9 REGULATORS SLIMLINE 2 OCTO SECOND STAGE 4. Hold the Second Stage with the MOUTHPIECE facing directly down, and gently shake it up and down. Listen carefully for any rattle that may be present, indicating LEVER ARM slack. If LEVER ARM slack is present, perform the following procedure: A.
-
Page 10: Parts List And Exploded View Diagram
REGULATORS SLIMLINE 2 OCTO SECOND STAGE Dia. Dia. Part # Description Part # Description 2.010 O-RING, ORIFICE 6789 GRILL, EXHAUST 6621 ORIFICE 6326 VALVE, EXHAUST 4330 COUPLING, INLET 6380 DIAPHRAGM 3.906 O-RING, COUPLING 6553 RING, FRONT COVER 4340 SEAT, POPPET 6554.18.1...
Need help?
Do you have a question about the SLIMLINE 2 OCTO and is the answer not in the manual?
Questions and answers