Summary of Contents for Baileigh Industrial DC-1650B
Page 1
REPRODUCTION OF THIS MANUAL IN ANY FORM WITHOUT WRITTEN APPROVAL OF BAILEIGH INDUSTRIAL HOLDINGS LLC, IS PROHIBITED. Baileigh Industrial Holdings LLC, does not assume and hereby disclaims any liability for any damage or loss caused by an omission or error in this Operator’s Manual, resulting from accident, negligence, or other occurrence.
THANK YOU & WARRANTY Thank you for your purchase of a machine from Baileigh Industrial Holdings LLC. We hope that you find it productive and useful to you for a long time to come. Inspection & Acceptance. Buyer shall inspect all Goods within ten (10) days after receipt thereof. Buyer’s payment shall constitute final acceptance of the Goods and shall act as a waiver of the Buyer’s rights to inspect or...
Page 4
We apologize for any discrepancies that may occur. Baileigh Industrial Holdings LLC reserves the right to make any and all changes deemed necessary in the course of business including but not limited to pricing, product specifications, quantities, and product availability.
INTRODUCTION The quality and reliability of the components assembled on a Baileigh Industrial Holdings LLC machine guarantee near perfect functioning, free from problems, even under the most demanding working conditions. However, if a situation arises, refer to the manual first. If a solution cannot be found, contact the distributor where you purchased our product.
IMPORTANT PLEASE READ THIS OPERATORS MANUAL CAREFULLY It contains important safety information, instructions, and necessary operating procedures. The continual observance of these procedures will help increase your production and extend the life of the equipment. SAFETY INSTRUCTIONS LEARN TO RECOGNIZE SAFETY INFORMATION This is the safety alert symbol.
Page 7
SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. PROTECT EYES Wear safety glasses or suitable eye protection when working on or around machinery. PROTECT AGAINST NOISE Prolonged exposure to loud noise can cause impairment or loss of hearing.
Power Switch with Lock Out In the event of incorrect operation or dangerous conditions, the machine can be stopped immediately by pressing the Power Switch paddle downward. Remove the yellow lock key to prevent the machine from starting. Note: Resetting the Power Switch WILL start the machine. SAFETY PRECAUTIONS Wood working can be dangerous if safe and proper operating procedures are not followed.
Page 9
2. Only trained and qualified personnel should operate this machine. 3. Make sure guards are in place and in proper working order before operating machinery. 4. Remove any adjusting tools. Before operating the machine, make sure any adjusting tools have been removed. 5.
20. Inspect power and control cables periodically. Replace if damaged or bare wires are exposed. Bare wiring can kill! 21. Maintain machine in top condition. Keep clean for best and safest performance. Follow instructions for lubricating and changing accessories. 22. Reduce the risk of unintentional starting. Make sure switch is in “OFF” position before plugging in power cord.
UNPACKING AND CHECKING CONTENTS Your Baileigh machine is shipped complete. Separate all parts from the packing material and check each item carefully. Make certain all items are accounted for before discarding any packing material. WARNING: SUFFOCATION HAZARD! Immediately discard any plastic bags and packing materials to eliminate choking and suffocation hazards to children and animals.
TRANSPORTING AND LIFTING NOTICE: Lifting and carrying operations should be carried out by skilled workers, such as a truck operator, crane operator, etc. If a crane is used to lift the machine, attach the lifting chain carefully, making sure the machine is well balanced. Follow these guidelines when lifting with truck or trolley: •...
• LEVELING: The machine should be sited on a level, concrete floor. Provisions for securing it should be in position to prevent the machine from moving inadvertently. • POWER SUPPLY PLACEMENT: The power supply should be located close enough to the machine so that the power cord is not in an area where it would cause a tripping hazard.
ASSEMBLY AND SET UP WARNING: For your own safety, DO NOT connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. 1. To assemble, first place the base plate upside down and attach the four casters to the holes provided and tighten with the wrench.
Page 17
3. Install the seal and connector to the collector body assembly using eight screws provided. (See FIG. 3 & FIG. 4) (FIG.3) (FIG.4) 4. Next install the seal and collector to the outlet. (See FIG. 5 & FIG. 6) (FIG. 5) (FIG.
Page 18
5. The collector support can now be mounted to the base plate as shown. (See FIG. 7) (FIG. 7) 6. At this time the upper bag support should be installed onto the collector support as shown in FIG. 8 (upper bag support may look different than shown) 7.
Page 19
9. The vacuum is now ready to be placed into service. Before connecting to a power source, be sure the power source is properly grounded and is of proper voltage and amperage. (See FIG. 9) (FIG. 9)
ELECTRICAL CAUTION: HAVE ELECTRICAL UTILITIES CONNECTED TO MACHINE BY A CERTIFIED ELECTRICIAN! Check if the available power supply is the same as listed on the machine nameplate. WARNING: Make sure the grounding wire (green) is properly connected to avoid electric shock. DO NOT switch the position of the green grounding wire if any electrical plug wires are switched during hookup.
• Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
Part List Item Description Specification Qty. Caster Flange Bolt 5/16” x 1/2” Support Base Plate Screw PAN. HD. 3/16” x 3/8” Inlet Cover Screw HEX. SOC. HD. M6 x 20 Hex Head Bolts. 3/8” x 1/2” Washer Impeller 12” Collector Body & Fan/Motor Assembly Washer 5/16”...
Page 24
BAILEIGH INDUSTRIAL HOLDINGS LLC 1625 D , WI 54220 UFEK RIVE ANITOWOC : 920. 684. 4990 F : 920. 684. 3944 HONE www.baileigh.com BAILEIGH INDUSTRIAL HOLDINGS LTD. U WIFT OINT WIFT ALLEY NDUSTRIAL STATE UGBY , CV21 1QH U IDLANDS...