Description (Fig. A) - DeWalt XR LI-ION DCH133N Original Instructions Manual

Example:
2019 XX XX
Year of Manufacture

Description (Fig. A)


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Battery pack
1
Battery release button
2
Side handle
3
Forward/reverse control
4
button (Lock-off button)
Trigger switch
5
Mode selector dial
6
Intended Use
Your heavy-duty cordless rotary hammerdrill is designed
for professional concrete drilling, screwdriving and
chiseling applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
Your heavy-duty cordless rotary hammerdrill is a professional
power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 1 with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
2
out of the tool handle.
Mode selector release
7
button
Depth rod
8
Depth rod adjust button
9
Main handle
10
Bit holder
11
WALT battery packs and chargers.
is fully charged.
1
and firmly pull the battery pack
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Belt Hook (Optional Accessory) (Fig. H)

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook
for tethering or securing the tool to a person or
object during use. DO NOT suspend tool overhead or
suspend objects from the belt tool.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.
IMPORTanT: When attaching or replacing the belt hook, use
only the screw 16 that is provided. Be sure to securely tighten
the screw.
The belt hook 15 can be attached to either side of the tool
using only the screw provided, to accommodate left- or
16
right- handed users. If the hook or magnetic bit holder is not
desired at all, it can be removed from the tool.
To move belt hook, remove the screw
place then reassemble on the opposite side. Be sure to securely
tighten the screw.
Side Handle and Depth Rod (Fig. A, C)

WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
The side handle 3 clamps to the front of the gear case and
may be rotated 360˚ to permit right- or left-hand use. The side
handle must be tightened sufficiently to resist the twisting
action of the tool if the accessory binds or stalls. Be sure to grip
the side handle at the far end to control the tool during a stall.
To loosen side handle, rotate counterclockwise.
To Adjust the Depth Rod (Fig. C)
1. Push in and hold the depth rod release button
side handle.
2. Move the depth rod 8 so the distance between the
end of the rod and the end of the bit equals the desired
drilling depth.
EnGLIsh
16 that holds it in
on the
9
33