Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HANSCRAFT IN.K300
Summary of Contents for HANSCRAFT IN.K300
- Page 1 USER MANUAL IN . K 30 0...
- Page 2 Modern manufacturing YOUR COMFORT IS OUR WE ALWAYS CHOOSE THE COMMAND GREEN WAY Our design process is heavily influenced Instead of using shell lamination which by Martin Prochazka, MSc., the creates harmful styrenes as a by-product, physiotherapist of Czech leading we use high quality GreenShield sportsmen, who oversees that all our materials.
- Page 3 Modern manufacturing PRECISE EXECUTION OF STRICT QUALITY TESTING EVERY DETAIL BEFORE SHIPMENT We work with the latest technology Not one hot tub leaves our manufacture and machinery, currently also used in hall without a series of strict and automotive, aircraft and arms industry. thorough testing procedures.
-
Page 4: Table Of Contents
Contents Hot tub performance parameters ......Performance parameters of CELTIC SPAS hot tubs ....Performance parameters of PLUG &... -
Page 5: Hot Tub Performance Parameters
Hot tub performance parameters For your own safety and the safety of your product, please observe the following instructions. Read the following information carefully and follow the user manual exactly when using the hot tub to avoid damaging the product or the risk of injury. This appliance is intended for use by children 8 years of age or older with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, provided they are under supervision or have been instructed on the use of the... -
Page 6: Performance Parameters Of Plug & Play Hot Tubs
Performance parameters/Installation preparation circuit breaker with a rated current of 16 A (motor circuit breaker) downstream of the Residual Current protective Device. Recommended Type C or D circuit breaker (motor circuit breaker) Hot tubs with two massage motors: 3× 16 A/C or D Hot tubs with three massage motors: 3×... -
Page 7: Preparation Of The Place For Installation And Connection To Electricity
Hot tub installation preparation Preparation of the place for installation and connection to electricity The hot tub must be installed on a flat, sufficiently strong pad with regard to the load-bearing capacity of the hot tub. If the hot tub is installed outdoors, we recommend making a monolithic concrete pad with a minimum thickness of 10 cm. -
Page 8: Hot Tub Installation
Hot tub installation Hot tub installation Attention: the hot tub must be connected pursuant to standards valid in the Czech Republic according to ČSN 33 2000 -7-701 General information For the installation, electrical connection and the first commissioning of the hot tub, we recommend using the services of professionally trained technicians. -
Page 9: Starting The Hot Tub Power Supply
All functions such as switching, volume control, etc. are controlled from the connected device. In some cases, the connection to the audio system is conditioned by a password, in which case enter 0000 as the password. Control panel (IN.K300) Panel description jets... -
Page 10: Start Or Stop Accessories
Control panel JETS The button is used for quick control of massage jets. In case it doesn't run filtration, the JETS button must be pressed twice. The power of water flow nozzles can be adjusted by turning the nozzles left or right. If so water does not flow through the nozzle, it does not have to be a fault, the nozzle can only be closed. -
Page 11: Program Menu
Control panel 30 minutes to warn you that the system is about to resume its normal operation. Press JETS to restart the system before the expiration of the 30 minute delay. When the system resumes its normal operation, the display shows “On” for 3 seconds. Program menu The program menu is accessible by holding down the Lights key for 5 seconds. -
Page 12: Programming The Filter/Purge Cycles
Control panel 1248 LIGHT (hold for 5 seconds) Programming the filter/purge cycles Depending on system configuration your spa will perform either a filter or a purge cycle. The filter cycle menu consists of the following parameters: the start time (FS), the duration (Fd) and the frequency (FF). The purge cycle menu consists of the following parameters: the start time (FS) and the frequency (FF). -
Page 13: Setting Filter Or Purge Cycle Frequency
Control panel (0 = no filtration, 24 = continuous filtration) It is not recommended to set this to “0”. F 03 5.10 Setting filter or purge cycle frequency The display will show FFXX, “XX” representing the number of cycles per day. Use the arrow keys to adjust the frequency. -
Page 14: Setting Economy Start Time
Control panel 5.12 Setting economy start time* The display will show ESXX, “XX” representing the hour at which the economy mode will become active. Use the arrow keys to adjust the hour. Use the Lights key to jump to the next parameter, economy duration (Ed). * Note that the parameters for the economy mode settings are associated to specific low level configuration of the syslem that are not present in all software revisions. -
Page 15: Smart Winter Mode
Control panel 5.15 Smart Winter Mode Our Smart Winter Mode protects your system from the cold by turning pumps on several times a day to prevent water from freezing in pipes. The “SWM” indicator lights up when freezing is detected and flashes when the purge is active. -
Page 16: Problem Solutions
Problem solutions Problem solutions The list below shows the different error messages that can appear on the home screen. Refer to the troubleshooting and error codes section of the TechBook for your spa pack for more details. ERROR MESSAGES Warning! HL Error No flow for more than 2 hours No flow condition Danger! Relay stuck... -
Page 17: Hot Tub Care
Hot tub care Hot tub care General information Do not expose the hot tub to sun without water inside or a cover on top. The direct sunlight can cause fading and deformation of the surface material. When you are not using the hot tub, cover it with the thermo cover, regardless of whether it is empty or full. - Page 18 Adjust the water pH level accordingly by suitable water chemicals (the HANSCRAFT SPA – pH PLUS and pH MINUS is recommended). Adjust the Cl (chlorine) level with suitable water chemicals (HANSCRAFT SPA – MULTI MINI 3 in 1 tablets are recommended). Follow the instructions on the chemicals‘...
-
Page 19: Replacing The Water
Hot tub care Replacing the water It is important to keep the hot tub water fresh and clean. We recommend you to replace the water at least every 3 months unless the water quality drops sooner. The hot tub water can be used for watering the garden for example, given that it has not been chemically treated at least one week prior. -
Page 20: Winter And Summer
Hot tub care Winter and summer The right balance of water chemicals represents an important factor in prolonging the longevity of your hot tub thermo cover. Remove the hot tub's cover and place it on the ground surface down. Wash the cover with a large amount of water from a garden hose or a water bucket. Clean the thermo cover surface using a soft brush and a mild dish soap solution (1 tea spoon of dish soap per 8 litres of water). -
Page 21: Summer Time
Winter and summer/Final information If the instructions above are not complied with and it results in a damage of the hot tub, the warranty cannot be claimed. Summer time Do not expose the hot tub to direct sunlight; do not use inappropriate cleaning detergents for upkeep. -
Page 22: Service Table
Service table/Supplements/Notes 10 Service table A TABLE FOR YOUR NOTES, PLEASE FILL OUT THE FOLLOWING INFORMATION. You will need the filled out information in case of a repair requested through the customer service line. Purchase date Delivery date Model name Serial number Seller information (name, phone number) - Page 23 Notes...
- Page 24 13. 8. 2021 HANSCRAFT, s.r.o. Safety K Vodojemu 140 Regular 252 19 Chrášťany u Prahy Production CZECH REPUBLIC Surveillance w w w. H A N S C R A F T.eu w w w.tuv.com ID 0000073072...
Need help?
Do you have a question about the IN.K300 and is the answer not in the manual?
Questions and answers