Page 3
overview IMPORTANT SAFETY INSTRUCTIONS 22. This device has been verified using STP cable. The use of appropriate GND grounding and STP cable is recommended to effectively protect your product and property from transient voltage, thunderstroke, communication interruption. 1. Read these instructions. WARNING 2.
Page 4
overview Class construction Please read the following recommended safety precautions carefully. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a ~ Do not place this apparatus on an uneven surface. protective earthing connection. ~ Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area.
CONTENTS OVERVIEW Important Safety Instructions WEB VIEWER Connecting to the Camera Recommended PC Specifications Password setting Recommended Micro SD/SDHC/SDXC Login Memory Card Specifications Camera Web Viewer Setup NAS recommended specs What’s Included Optional Accessories for Installation At a Glance APPENDIX Troubleshooting INSTALLATION &...
overview RECOMMENDED PC SPECIFICATIONS WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. ~ CPU : Intel(R) Core(TM) i7 3.4 GHz or higher (As for each sales country, accessories are not the same.) ~ RAM : 8G or higher ~ Recommended browser: Chrome Appearance...
OPTIONAL ACCESSORIES FOR INSTALLATION Appearance Item Name Quantity Description You can purchase appropriate optional accessories available. Screws used for mounting your camera on the hanging Machine Screws mount, GangBox, etc. Product type Wall mount Model Name SBP-300WMW1 Cap Installer Used to connect the RJ45 cable. Used for dome cover disassembly, Screw bit assembly and camera installation.
overview AT A GLANCE Components (Front Side) Appearance Item Description Lens 4 camera lenses create a panoramic image. The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. If you reset the camera, the network settings will be adjusted so that DHCP can be Reset Button enabled.
Page 9
Components (Rear Side) Item Description This port connects power and network via PoE+ injector. PoE+ port Power port (DC 12 V) Port for power terminal block. English _9...
installation & connection INSTALLATION 2. Loosen the fastening screw on the camera body. You don’t have to completely remove the screws. This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Page 11
Inserting a Micro SD card Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD 1. Remove the dome cover of the camera. card from the slot.
Page 12
installation & connection Installation (mount plate) 1-3. Pull out necessary cables among network/power/audio/alarm cables through the hole in the mount plate. [Directly installing on ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. [Installing using pipe] 2-1.
Page 13
2-3. Place the pipe on the mount plate. [Attaching to the unbundled adapter] 2-4. Fix the mount plate using appropriate screws. Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience. 3-1.
Page 14
installation & connection Installation (camera body and dome cover) [Installing network/power cables] 1. Connect the safety wire. Use a cable bushing compliant with the network cable to be connected. Camera main: use a cable with the diameter of Ø5 to 6.5 Components: use a cable with the diameter of Ø7 to 8.5 3-1.
Page 15
3-5. Connect the network cable connector to the PoE+ port, and connect the power terminal block to the 4-3. Mount the cable bushing to the camera body. power port. [Installing the network cable] (IP66) 4-4. Connect the network cable jack to the PoE+ port of the camera. 4-1.
Page 16
installation & connection [Installing audio/alarm cables] 7. Lift up the camera body and push the mounting clips until they click into place. 5. Plug the cable bushing of the provided audio/alarm cable into the camera body. 8. Using the fastening screws on the camera body, fix the camera body to the mount plate. 6.
Page 17
9. Adjust the lens to the desired direction by referring to “Adjusting the monitoring direction for the Adjusting the monitoring direction for the camera camera”. If you tilt the lens, you may need to adjust the lens as this may block the screen. 10.
WiFi dongle 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB port. Smartphone Setup 1. Install the Wisenet Installation application. 2. Select the camera SSID after turning on the WiFi. 3. Run the Wisenet Installation application. 4. When you log in to the camera, the video will be connected.
Page 19
Power Cable Specification Connecting to Audio Input/Output In case of DC 12 V Input: Wire Type (AWG) Cable Length (Max.) 15 m 25 m Speaker Network Cable Specification Item Contents Remark Connector RJ45 (10/100/1000BASE-T) Microphone To operate with 1000BASE-T, a cable of Ethernet 10/100/1000BASE-T UTP-6 or higher should be used for the...
Page 20
installation & connection Connecting to the I/O port box To connect the external sensor Connect the Alarm I/O cable to the corresponding port of the port box. Connect one of the 2 signal lines to the [ALARM #1] port (if you want this to be the input port) and the remaining one to the [GND] port.
network connection and setup CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE You can set up the network settings according to your network configurations. MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET 1.
network connection and setup USING DEVICE MANAGER If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. Device manager program can be downloaded from <Technical Guides>-<Online Tool> menu at Hanwha Techwin website ex) 192.168.1.2~254, 192.168.0.2~254, (http://www.hanwha-security.com).
~ Example of the Dynamic IP environment configure the IP. PNM-9022V - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2. Click < + > at the main page of device manager.
Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function. For more information, refer to the user manual of the applicable router. After connecting the network camera, select the checkbox from the menu <Quick connect> in <Wisenet DDNS> in “Settings -> Network -> DDNS”.
2. From the remote PC, launch the Internet browser and type the DDNS URL address of the camera, or the IP address of the Broadband Router in the address bar. ex) http://ddns.hanwha-security.com/ID To use Wisenet DDNS, sign up at the Wisenet DDNS homepage (http://ddns.hanwha-security.com) and register the product at [My DDNS]>[Register Product]. English _25...
To register your device to the <DDNS> server, visit http://ddns.hanwha-security.com and register your device 1. Launch the Internet browser. first, and then set the Web Viewer’s <Network> - <DDNS> to <Wisenet DDNS>, as well as providing <Product ID> that had been used for DDNS registration.
PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the 1. Click the [Setup ( )] icon. login password. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and For a new password with 8 to 9 digits, you must use at least 3 of system over the network.
appendix TROUBLESHOOTING PROBLEM SOLUTION ~ Verify the settings in the following sequence: <Motion detection> of <Analytics> is PROBLEM SOLUTION set to <Enable>, but no notification A. Check <Data & Time> settings. ~ On the authentication popup window prompted when initially accessing https, click "View e-mail reaches me even when an B.
Page 29
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the PNM-9022V and is the answer not in the manual?
Questions and answers