Table of Contents
Advertisement
R2E220-AB08-12
3.2 Nominal data
Motor
M2E068-CF
Phase
1~
Nominal voltage / VAC
115
Frequency / Hz
50
Method of obtaining
fa
data
Valid for approval/
-
standard
-1
Speed (rpm) / min
2750
Power consumption / W
93
Current draw / A
0.8
Capacitor / µF
10
Capacitor voltage / VDB
220
Capacitor standard
S0 (CE)
Min. back pressure / Pa
0
Min. ambient
-25
temperature / °C
Max. ambient
30
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
1.74 kg
Size
220 mm
Motor size
68
Rotor surface
Painted black
Impeller material
PA6 plastic, glass-fiber reinforced
Number of blades
11
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP44; installation- and position-dependent
as per EN 60034-5
Insulation class
"B"
Moisture (F) /
H1
Environmental (H)
protection class
Installation position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
On rotor side
drainage holes
Mode
S1
Motor bearing
Ball bearing
Touch current
< 0.75 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Motor protection
Thermal overload protector (TOP)
internally connected
with cable
Variable
Protection class
I (with customer connection of protective
earth)
Conformity with
EN 60034-1; EN 60204-1; EN 60335-1
standards
Comment on CE
Commissioning not permitted in the
European Economic Area
Item no. 10535-5-9970 · ENU · Change 226988 · Approved 2021-03-24 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
1~
1~
115
115
60
60
fa
fa
-
UL 2111
3050
3050
125
130
1.1
1.15
10
10
220
220
S0 (CE)
UL
0
0
-25
-25
35
35
Approval
CSA C22.2 No. 77; CCC; UL 1004-3
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
; Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
3.4 Mounting data
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Strength class of
8.8
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
locking screws).
3.5 Transport and storage conditions
Max. permitted
+80 °C
ambient temp. for
motor (transport/
storage)
Min. permitted
-40 °C
ambient temp. for
motor (transport/
storage)
Advertisement
Table of Contents
