Table of Contents
Advertisement
Quick Links
User Instruction & Installation Manual
A6172 – 110/240v Deck
A6173 – 110/240v Cabin
A6174 – 110/240v Deck Pedestal
A6175 – 110/240v Cabin Pedestal
Manufacturer's details:
Francis Searchlights Ltd
Union Road, Bolton
Lancashire, BL2 2HJ, UK
Tel:
+44 (0) 1204 558960
Fax:
+44 (0) 1204 558979
http://www.francis.co.uk
E-mail: sales@francis.co.uk
L300 110w Searchlight
Product Reference Number:
Manual Part Number: C27731
Issue: 4
A7201 – 24v Deck
A7228 – 24v Cabin
A7229 – 24v Deck Pedestal
A7230 – 24v Cabin Pedestal
Distributor details:
4.2.20
Advertisement
Table of Contents
Related Manuals for Francis Searchlights A6172
Summary of Contents for Francis Searchlights A6172
- Page 1 User Instruction & Installation Manual L300 110w Searchlight Product Reference Number: A6172 – 110/240v Deck A7201 – 24v Deck A6173 – 110/240v Cabin A7228 – 24v Cabin A6174 – 110/240v Deck Pedestal A7229 – 24v Deck Pedestal A6175 – 110/240v Cabin Pedestal A7230 –...
-
Page 2: Table Of Contents
CONTENTS - Introduction - Safety Precautions - Technical Information - Unpacking and Installation Instructions - Electrical Installation - Operating Instructions - Fault Finding - Maintenance and Servicing - Wiring Diagrams & General Assemblies - Spare Parts List Back To Top... -
Page 3: Introduction
For your future reference please keep this manual in a safe place. Thank you for specifying a product from the Francis Searchlights range. All Francis products are designed to give complete customer satisfaction and are manufactured to the highest engineering standards in order to ensure optimum performance and service life. -
Page 4: Safety Precautions
2 - Safety Precautions The following instructions must be adhered to, in order to ensure a safe working environment and the safety of the user. Note: When unpacking or manoeuvring the searchlight into its fixing position, suitable lifting points must be used in order to prevent damage to the equipment or personal injury. ◼... -
Page 5: Unpacking And Installation Instructions
4 - Unpacking and Installation Instructions The following instructions should be read and fully understood prior to installing the equipment to ensure that the correct procedures are followed, and all safety precautions are observed. Note: If the equipment has been in storage for a considerable amount of time, it is advisable to conduct a routine maintenance check on all parts before installation. - Page 6 Fitting Instructions for Cabin Model Preparing the Mounting Position Using the template provided mark out and drill the fixing holes through the deck or cabin roof. In the case of cabin control models, a centre hole is also required to allow the mechanism to pass through.
- Page 7 5.Remove the Blanking Plug 6.Insert the Under Deck through the centre hole making sure it’s aligned as photos below from the Bellows Bottom Bush. 7. Fasten the Under Deck mechanism Using the 3 off M6 x 16 screws 8. Re-Fit the following items: and spring washers Push Rod Top Bush 9.Bellows Top Bush.
- Page 8 12. Make sure the mechanism is in this position before tightening the M5 x 8 hexagon screw onto the flat of the push rod 13.U-Piece fixings. 14. Fix the U-Piece Assembly using U-Piece fixings make sure there is a plain washer both sides of the U-Piece Bush.
-
Page 9: Electrical Installation
5 - Electrical Installation For safety purposes, only competent personnel should perform the electrical installation. All equipment should be installed to current Electrical Regulations and Standards. In order to obtain the maximum light output from the searchlight, it is essential that the full operating voltage of the LED fitted be applied to the LED contacts. -
Page 10: Operating Instructions
6 - Operating Instructions This equipment is designed for use out of doors, in free air. Never place anything on or cover the searchlight when in use as this may present a hazard. The searchlight can be positioned using the elevation and base plate lockwheels. When in the desired position the lockwheels should be securely fastened to maintain position. -
Page 11: Fault Finding
7- Fault Finding All fault finding must be conducted by a competent person or qualified Electrical Engineer. Failure of LED to light. In the event of the LED failing to light the following steps should be taken: 1) Check that the mains supply is connected to the input of the LED driver and check all connections as per the wiring diagram. -
Page 12: Wiring Diagrams & General Assemblies
9 - Wiring Diagrams & General Assemblies Drawing Number Description A6172 L300 110W LED Deck 110/240V General Assembly A7201 L300 110W LED Deck 24V General Assembly A6173 L300 110W LED Cabin 110/240V General Assembly A7228 L300 110W LED Cabin 24V General Assembly... -
Page 21: Spare Parts List
Searchlights spare parts. This will ensure that any warranties on your equipment will not be invalidated. When ordering spare parts please contact the Sales Department at Francis Searchlights Limited. Please quote searchlight model and serial number at all times. This will enable a fast response to your spares’...