CONTENTS safety precautions…………………………………………………………………………..……………3 TV block diagram and PHILIPS UOC functional difference between the various IC versions …………….…..…….4 3. Replacement of memory IC………………………………………………………… …………………7 4. Service adjustment………………………………………………………… ………………………...7 5. ICs functional description………………………………………………………………………………9 6. Test point waveform………………………………………………………………………………….…12 7. All ICs/transistors voltages…………………………………………………………………………….13 8. Purity / convergence adjustment……………………………………………………………………..14 9....
Page 5
1.SAFETY PRECAUTIONS (Safety for Electrical Shock Hazard) The design of this product contains special hardware, many circuits and components specially for safety purposes. For After re-assembling the product, always perform an isolation continued protection, no changes should be made to the check on the exposed metal parts of the cabinet (antenna original design unless authorized in writing by the terminals, video/audio input and output terminals, Control...
Page 6
2. TV Block diagram TUNER TDA93XX video IF IN Y IN 4052 video RF AGC V IN U IN video TRAP video S-VHS CVBSINT video CHROMA IFVO OUT 24C04 audio CVBS/Y IN ARi2 ARi1 TDA9874 XS303 TDA9859 ALi2 AUDIO OUT RGB OUT ALi1 audio...
3.REPLACEMENT OF MEMORY IC 1. MEMORY IC. This TV uses memory IC. In the memory IC are memorized data for correctly operating the video and deflection circuits. When replacing memory IC, be sure to use IC written with the initial value of data. 2.
Page 10
MENU0 Geometrical adjustment Receive PAL standard Complete pattern signal. Adjustment steps: a) Adjust V. SLOPE, to the center horizontal line just appeare from half bottom shadow. b) Adjust V. SIZE, to get 90% of vertical picture contents would be displayed on CRT. c) Adjust V.
5. ICs functional description UOC TDA93XX SYMBOL DESCRIPTION STAND BY output. In STAND BY mode, high level (Power OFF). For Power ON this pin will be reduced to low. C-bus clock line C-bus data line TUNING tuning Voltage (Vt) PWM output P3.0/NTSC SW Port 3.0 or NTSC output/SCART SW input, Forced NTSC selection, Low-level output, otherwise High output.
Page 13
G input / Y input G2/YIN B input / U (B-Y) input / P input B2/UIN BCLIN beam current limiter input BLKIN black current input / V-guard input Red output Green output Blue output VDDA analog supply of Closed Caption decoder and digital supply of TV-processor (3.3 V) OTP Programming Voltage VDDC digital supply to core (3.3 V)
LA78040/78045 Function : vertical output Symbol Function Symbol Function INV IN Input V OUT Vertical output VCC1 Power VCC2 Output power supply PUMP UP Pump up power NON INV IN Negative feedback Ground TDA9859 Function : Universal Sound processor Symbol Function Symbol Function...
Page 15
7. IC voltages TDA93XX LA76040 15.9 -0.07 AN 7522 TDA9859...
8. PURITY / CONVERGENCE ADJUSTMENT PURITY ADJUSTMENT WEDGE DEFLECTION Demagnetize CRT with the demagnetizer. YOKE Loosen the retainer screw of the deflection yoke. Remove the wedges. Input a green raster signal from the signal generator, and turn the screen to green raster. Move the deflection yoke backward.
Page 17
STATIC CONVERGENCE ADJUSTMENT 1. Input a crosshatch signal. 2. Using 4-pole convergence magnets, overlap the red and blue lines in the center of the screen (Fig. 1) and turn them to magenta (red/blue). (FRONT VIEW) 3. Using 6-pole convergence magnets, overlap the magenta (red/blue) and green lines in the center of the screen and turn them to white.
9. List of Parts NAME TYPE Q'TY REMARK CU-2988(AUSTRALIA) PC BOARD MODULE CRT BOARD MODULE KEY AND REMOTE CONTROL BOARD MODULE PRINTED CIRCUIT BOARD TOUCH SWITCH KFC-A06-21050 TOUCH SWITCH KFC-A06-21050 TOUCH SWITCH KFC-A06-21050 TOUCH SWITCH KFC-A06-21050 TOUCH SWITCH KFC-A06-21050 TOUCH SWITCH KFC-A06-21050 CARBON FILM RESISTOR RT13-1/6W-470Ω-J-T52...
Page 19
POWER CABLE POWER SWITCH POWER TRANSMITTING WIRE PACKING ARK MODULE POWER CABLE PLASTIC BAG WIRE 60mm OPERATION INTRODUCTIONS(ENGLISH) TEAC PROPAGANDIZE PAGE POP STATIC FILM (ENGLISH) BATTERY REMOTE CONTROL OPERATION INTRODUCTIONS PLASTIC BAG 29“90 SERIES INTEGER PLASTIC BAG PACKING ARK ENCASEMENT NAIL...
Page 27
UOC TDA9373 SERIES COLOUR TELEVISION PUSH PUSH CT-M6845...
Page 28
CONTENTS safety precautions…………………………………………………………………………..……………3 TV block diagram and PHILIPS UOC functional difference between the various IC versions …………….…..…….4 3. Replacement of memory IC………………………………………………………… …………………7 4. Service adjustment………………………………………………………… ………………………...7 5. ICs functional description………………………………………………………………………………9 6. Test point waveform………………………………………………………………………………….…12 7. All ICs/transistors voltages…………………………………………………………………………….13 8. Purity / convergence adjustment……………………………………………………………………..14 9....
Page 29
1.SAFETY PRECAUTIONS 10. Isolation Check The design of this product contains special hardware, many (Safety for Electrical Shock Hazard) circuits and components specially for safety purposes. For continued protection, no changes should be made to the After re-assembling the product, always perform an isolation original design unless authorized in writing by the check on the exposed metal parts of the cabinet (antenna manufacturer.
Page 30
2. TV Block diagram TUNER TDA93XX video IF IN Y IN 4052 video RF AGC V IN U IN video TRAP video S-VHS CVBSINT video CHROMA IFVO OUT 24C04 audio CVBS/Y IN ARi2 ARi1 TDA9874 XS303 TDA9859 ALi2 AUDIO OUT RGB OUT ALi1 audio...
3.REPLACEMENT OF MEMORY IC 1. MEMORY IC. This TV uses memory IC. In the memory IC are memorized data for correctly operating the video and deflection circuits. When replacing memory IC, be sure to use IC written with the initial value of data. 2.
Page 34
MENU0 Geometrical adjustment Receive PAL standard Complete pattern signal. Adjustment steps : a) Adjust V. SLOPE, to the center horizontal line just appeare from half bottom shadow. b) Adjust V. SIZE, to get 90% of vertical picture contents would be displayed on CRT. c) Adjust V.
Page 35
ENGLISH ON/OFF HSHIFT 0~63 ARABIC ON/OFF PERSIAN ON/OFF 0~63 TURKISH ON/OFF 0~63 FRANCE ON/OFF RUSSIA ON/OFF 0~63 0~63 SHIPMODE 0~63 SEARCH SPEED 0~63 AGC-TOP 0~63 0~63 AGC-SPEED 0~63 2. TDA9361(1.1) EK cord=NTDA9361-----NF Items Variable Preset Items Variable Preset ON/OFF SUBCON 0~63 ON/OFF SUBCOL...
5. ICs functional description UOC TDA93XX SYMBOL DESCRIPTION STAND BY output. In STAND BY mode, high level (Power OFF). For Power ON this pin will be reduced to low. C-bus clock line C-bus data line TUNING tuning Voltage (Vt) PWM output P3.0/NTSC SW Port 3.0 or NTSC output/SCART SW input, Forced NTSC selection, Low-level output, otherwise High output.
Page 37
RGB / YUV insertion input INSSW2 R input / V (R-Y) input / P input R2/VIN G2/YIN G input / Y input B2/UIN B input / U (B-Y) input / P input BCLIN beam current limiter input black current input / V-guard input BLKIN Red output Green output...
In 1 Ch 1 input Out 2 (+) Ch 2 output (+) Note: AN7523 is pin 1 to 9, AN7522 is pin 1 to 12. LA78040/78045 Function : vertical output Symbol Function Symbol Function INV IN Input V OUT Vertical output VCC1 Power VCC2...
Page 39
7. IC voltages TDA93XX LA76040 15.9 -0.07 AN 7522 TDA9859...
8. PURITY / CONVERGENCE ADJUSTMENT PURITY ADJUSTMENT WEDGE DEFLECTION Demagnetize CRT with the demagnetizer. YOKE Loosen the retainer screw of the deflection yoke. Remove the wedges. Input a green raster signal from the signal generator, and turn the screen to green raster. Move the deflection yoke backward.
Page 41
STATIC CONVERGENCE ADJUSTMENT 1. Input a crosshatch signal. 2. Using 4-pole convergence magnets, overlap the red and blue lines in the center of the screen (Fig. 1) and turn them to magenta (red/blue). (FRONT VIEW) 3. Using 6-pole convergence magnets, overlap the magenta (red/blue) and green lines in the center of the screen and turn them to white.
9. List of Parts NAME TYPE Q'TY REMARK CU-2988(AUSTRALIA) PC BOARD MODULE CRT BOARD MODULE KEY AND REMOTE CONTROL BOARD MODULE PRINTED CIRCUIT BOARD TOUCH SWITCH KFC-A06-21050 TOUCH SWITCH KFC-A06-21050 TOUCH SWITCH KFC-A06-21050 TOUCH SWITCH KFC-A06-21050 TOUCH SWITCH KFC-A06-21050 TOUCH SWITCH KFC-A06-21050 CARBON FILM RESISTOR RT13-1/6W-470Ω-J-T52...
Page 43
POWER CABLE POWER SWITCH POWER TRANSMITTING WIRE PACKING ARK MODULE POWER CABLE PLASTIC BAG WIRE 60mm OPERATION INTRODUCTIONS(ENGLISH) TEAC PROPAGANDIZE PAGE POP STATIC FILM (ENGLISH) BATTERY REMOTE CONTROL OPERATION INTRODUCTIONS PLASTIC BAG 29“90 SERIES INTEGER PLASTIC BAG PACKING ARK ENCASEMENT NAIL...
Page 54
Overall Configuration: In this chassis, the single-chip IC OM8838/TDA8842 for color TV small signal processing with I C bus control of the Phillips is used. It can be used on all models from 14” to 29”. It has a number of expansion functions, and a series of color TV sets, from simple to high grade and of a number of systems, such as PAL, NTSC and SECAM can be made on a single PCB master board Specification...
Page 55
Rear view diagram ⑧AV IN sockets ⑧ Antenna input and AV IN/OUT sockets Remote controller diagram CALL SLEEP CLEAR FEATURE PICTURE PRESET MUTE SOUND - 3 -...
Page 56
一. Introduction to IC’s 1. TDA8842 (OM8838) multi-system small signal processing IC TDA8842 (OM8838) is the new type Video/Chroma/Deflection (V/C/D) processing chip developed by the Phillips in 1998, i.e., the Video/Chroma/Deflection small signal processing IC. By fully adopting the I C bus control technique and integrating a number of unique circuits into the chip, it has greatly simplified the elements external to the IC and achieved overall improvement in the picture and sound quality of the popular model color TV sets.
Page 57
This unit circuit consists of four sections, i.e., vertical serrated wave generator, vertical geometric correction processor, horizontal (E-W) geometric correction processor, EHT follow-up and over-voltage protection circuit, as detailed in Fig. 5. Filter CVBS/Y/C switching unit circuit The filter CVBS/Y/C switching unit circuit has such main functions: selective filtering correction for input composite video signal CVBSINT, output composite video signal CVB-SEXT, CVB/Y and chroma signal C;...
Page 58
Pin ① Tuning voltage output (functioning only to VST tuner, and it has no output when the IIC bus has identified the presence of a FST tuner.) Pin ② left channel volume control output Pin ③ right channel volume control output (Note: Pins ② and ③ have PWM output only when there is no output from IIC) Pin ④...
Page 59
Ground Pins are respectively for B,G,R screen character display output (Note: the 23 24 blue background in this machine is produced inside OM8838) blanking signal output horizontal synchronization signal input (positive polarity) vertical synchronization signal input (positive polarity) ground not used in this machine Pins 12MHz reset...
Page 60
input serial data 4.85 4.85 input and output Bandgap 6.67 12.5 decoupling DHROMA Chroma input 1.12 1.12 CVBA/Y External CVBS/Y 3.35 3.35 input Main power supply 7.80 7.80 voltage (+8V) CVBSY Internal CVBS 3.35 3.35 input GND1 Ground1 AUDIOUT Audio interface 2.98 2.98 Internal connection 0...
Page 61
connection port Loop filter phase 4.31 detector Second supply 7.83 voltage (+8V) CVBSIO CVBS-1 output 2.46 3.54 DECDIG Digital supply end 4.91 decoupling H OUT Horizontal output 0.41 0.41 FBISO Flyback input/ 0.56 0.77 sandcastle output PH2LF Phase 2 filter 3.41 3.44 13.5...
Page 62
Pins Sound signal output (11 as positive and 13 as negative) 11 13 Ground TDA7056 (mono) Pin No. Function Blank Pin ① Sound working power supply (+14V-16V) Pin ② Audio signal input Pin ③ Ground Pin ④ Sound volume DC level control Pin ⑤...
Page 63
Video amplification voltage (+180V) Pin ⑨ Blank Pin ⑩ [8] Video switch HEF4053 Three sets of SPDT switches Output 1 ① ③ ⒀ 1IN1(1) 2IN1(0) 3IN1(1) ④ ② ⑤ ⑿ 1IN2(0) 2IN2(1) 3IN2(0) ⑨-- Control pin Control pin Control pin +5V power supply Pins ⑥⑦⑧...
Page 64
*V-ZOOM: set value 25 *V-SCORLL: set value 31 Note: The vertical adjustment for PAL system signal and NTSC system signal should be adjusted separately. Press the “Maintenance” key three times to enter the third menu under factory status, which gives the following display: Remarks: MTV880C.
Page 65
Press the “Maintenance” key six times to enter the sixth menu, which gives the following display: Remarks: MTV880C. No item in this menu will function in the adjustment of this Y-CTI-DELAY 4 chassis. ADAP. BLACK 32 0-63 LUM. LINER 32 0-63 GAMMA 32 0-63 PEARING...
Page 66
Press the “Maintenance” key nine times to enter the ninth menu, which gives the following display: Remarks: OPTION2 * AV1: set value 1 *AV2: set value 1 (0 for one channel of AV input) *AV3: set value 0 *SVHS: set value 1 (0 for 21” and 14”) SVHS *UI MODE: set value 2 UI MODE...
Page 67
white balance is classified as “dark white balance” and “bright white balance”. Dark white balance means the white balance when the screen is in dark condition because of high cathode voltage of the electron gun and low electron beam current, it corresponds to the color cast resulted from different electron flow cut-off characteristics of the beams from three guns, therefore dark white balance adjustment is actually an adjustment of the static bias voltage of the video amplifier.
Page 68
② Main points in color cast and retrace fault repair in 8838/8842 series color TV The traditional method to repair a color cast fault in color TV is to adjust the saturation, then observe if the picture turns to black and white after cutting off the saturation. If so, the fault is in the video amplification circuit or there is color cast in the CRT.
Page 69
OM8838/TDA8842 series color TV sets rely more on the “soft start and slow stop” function set inside the IC chip and the “automatic fault diagnosis” or logic protection function on some ports to realize protection for the circuit. In case of a fault in horizontal scanning, vertical scanning and video amplification circuits, the whole machine will be in the faulty status of “three no’s”...
Page 70
3. Quick checklist for common faults in TDA8842/OM8838 series color TV sets: Fault symptom Faulty unit circuit Faulty element Three no’s, the indicator Power supply Fuse F801 damaged, and resistor R802 is not ON section damaged Three no’s, the indicator Power supply Fuse F801 damaged, and diodes D801, D802,...
Page 71
Parts No. Description Qty Location 03000000 PARTS E9680030 GROUND LINE DISCRETENESS F6470290 POWER WIRE 04000000 PART G0610760 RADIATING PIN(5V,8V) G0610760 RADIATING PIN(5V,8V) RADIATING PIN(CUSION) G0610790 G0610840 RADIATING PIN(12V) G0611140 RADIATING PIN(H.) G0611150 RADIATING PIN(R.) G0611160 RADIATING PIN(SOUND) G0611240 RADIATING PIN(POWER) G3600010 ISINGLASS PARCEL G7310000...