Intended Use Statement The 3M Pocket Projector MPro120 is designed to operate with the 3M-specified battery and ™ 3M battery charger and in a normal office and home environment. • 10˚–35˚C (50˚–95˚F) • 10–80% RH (without condensation) • 0–1829 m (0–6000 feet) above sea level The ambient operating environment should be free of airborne smoke, grease, oil and other contaminants that can affect the operation or performance of the projector.
Page 5
Warning To reduce the risk associated with hazardous voltage: • Do not modify this product in any way. Use only 3M approved replacement components. • Do not attempt to service this projector other than battery replacement. There are no user serviceable parts other than the battery. Service to be performed only by a 3M-authorized service provider using 3M-approved system components.
Page 6
• Do not immerse the battery in water or allow to get wet. • Do not reverse the positive(+) and negative(-) terminals. • Do not connect the battery directly to a wall outlet. Use only the 3M-specified wall charger or automobile charger.
Page 9
RoHS, as amended:(a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. This information represents 3M’s knowledge and belief, which may be based on information provided by third party suppliers to 3M.
Getting Started Install Battery The 3M MPro120 comes with a rechargeable battery. The battery is quick and easy to install and comes partially charged. To install the battery: slide the back cover off, insert the battery, and reinstall the cover.
Page 13
The power adapter is used to charge the battery or power the projector. There are four outlet adapters to give you the flexibility to power the 3M MPro120 in most countries. You can also power the projector with the 3M MPro120 Car Charger, available separately.
Page 14
Charge the Battery The 3M MPro120 rechargeable battery gives you up to 4 hours of battery life in normal brightness mode. When the battery needs to be charged, the Status Indicator will flash red. The battery is charged by connecting the 3M MPro120 power adapter to the projector.
Page 16
Connecting to a Component Video Device For component video input, you must purchase the optional 3M MPro120 Component AV Cable. This cable sends a higher quality video signal for the best possible image. Connect the Component AV cable to the projector’s VGA-AV input.
Page 18
(PDAs). The projector supports VGA, SVGA, XGA, and WXGA resolutions. Connect the VGA Cable to the MPro120 projector. Connect the VGA Cable to the computer’s video and audio outputs. Set the computer resolution to one of the supported resolutions.
Adjusting Image Size The 3M MPro120 can project an 8 to 50 inch (203–1270 mm) diagonal image. Refer to the chart below. Diagonal SIze Image Width 8 in (20.32 cm) 6 3/8 in (16.2 cm) 14 in (35.56 cm) 11 1/4 in (28.4 cm) 20 in (50.8 cm)
Page 22
Attaching the Tripod The projector includes a table top tripod that mounts to the bottom of the projector. Tip: The 3M MPro120 will attach to most camera tripods. Cleaning Projector Turn off the projector and disconnect power and other cables.
The battery needs to be charged. See “Charge the Battery” on page 14. The image is not visible or is very dim. • The 3M MPro120 is a battery operated projector and requires controlled lighting conditions. The image may appear very dim in brightly lit rooms. •...
Page 25
My video device is connected to the projector but the projector will not display the video. • Unplug the AV cable from the projector and a white image with the 3M logo will display. • Plug the AV cable into the projector and the icon in the upper-left corner of the image will change from a “waiting on cable”...
3M. If the product is repaired, 3M will repair the defective part(s) with a new or used part(s). If the 3M product is replaced, 3M will replace the 3M product with the same or equivalent model and with a new or refurbished 3M product. In the case of an approved warranty claim, the replacement 3M product will carry only the remaining term of the original 3M product’s warranty period as stated above.
Page 29
0–1829 m (0–6000 feet) above sea level The air intake and exhaust vent must be clear of obstructions. Inadequate air ventilation will cause the 3M product to malfunction or will cause damage to the 3M product which will void the warranty.
Page 30
What 3M Will Do To Correct Problems: • If your 3M product requires service, 3M will ask you to bring or send the 3M product, securely packaged in its original container or equivalent, along with proof of the date of original purchase, to your 3M Service Dealer or 3M Service Center.
Need help?
Do you have a question about the MPro120 and is the answer not in the manual?
Questions and answers