Painting; Electronic Pressure Control Indicators - Titan Tool 1140ix Owner's Manual

7. Move the PRIME/SPRAY valve up to the SPRAY position.
8. Turn the unit on and set the pressure to minimum by
turning the pressure control knob to the "Min PSI" setting
in the yellow zone.
9. Unlock the gun by turning the gun trigger lock to the
unlocked position.
WARNING
Ground the gun by holding it against the
edge of the metal container while
flushing. Failure to do so may lead to a
static electric discharge, which may
cause a fire.
10. Trigger the gun into the metal waste
container until the old solvent is gone and fresh solvent is
coming out of the gun.
11. Lock the gun by turning the gun
trigger lock to the locked position.
12. Set down the gun and increase the
pressure by turning the pressure
control knob slowly clockwise into the
green zone.
13. Check the entire system for leaks. If
leaks occur, follow the "Pressure Relief Procedure" in this
manual before tightening any fittings or hoses.
14. Follow the "Pressure Relief Procedure" in this manual
before changing from solvent to paint.
WARNING
Be sure to follow the pressure relief procedure when
shutting the unit down for any purpose, including
servicing or adjusting any part of the spray system,
changing or cleaning spray tips, or preparing for cleanup.

Painting

1. Place the siphon tube into a container of paint.
2. Place the return hose into a metal waste container.
3. Move the PRIME/SPRAY valve down to the PRIME
position.
4. Turn the unit on and set the pressure to
minimum by turning the pressure control
knob to the "Min PSI" setting in the yellow
zone.
5. Allow the sprayer to run until paint is
coming through the return hose into the
metal waste container.
6. Turn the unit off by moving the pressure control knob to
the OFF position in the black zone.
7. Remove the return hose from the waste container and
place it in its operating position above the container of
paint.
8. Move the PRIME/SPRAY valve up to the SPRAY position.
9. Turn the unit on and set the pressure to minimum by
turning the pressure control knob to the "Min PSI" setting
in the yellow zone.
10. Unlock the gun by turning the gun trigger lock to the
unlocked position.
WARNING
Ground the gun by holding it against the
edge of the metal container while
flushing. Failure to do so may lead to a
static electric discharge, which may
cause a fire.
11. Trigger the gun into the metal waste
container until all air and solvent is flushed from the spray
hose and paint is flowing freely from the gun.
© Titan Tool Inc. All rights reserved.
12. Lock the gun by turning the gun trigger
13. Turn the unit off by moving the
14. Attach tip guard and tip to the gun as
POSSIBLE INJECTION HAZARD. Do not spray without the
tip guard in place. Never trigger the gun unless the tip is
in either the spray or the unclog position. Always engage
the gun trigger lock before removing, replacing or
cleaning tip.
15. Turn the unit on and set the pressure to minimum by
16. Increase the pressure by turning the pressure control
Trigger lock
in locked position.
NOTE: Turning the pressure up higher then needed to

Electronic Pressure Control Indicators

The following is a description of the electronic pressure control
indicators.
Min.
PSI
(Bar)
Max. PSI
Pressure Indicator
On/Off (Bar)
The pressure indicator shows the current operating pressure of
the sprayer. It has three different indications: blinking yellow,
solid yellow, and solid green.
Blinking Yellow
When the pressure indicator is blinking yellow, the sprayer is
operating between 0 and 200 PSI. A blinking yellow pressure
indicator means:
• The sprayer is plugged in and turned "ON".
• The sprayer is at priming pressure (little or no pressure).
• It is safe to move the PRIME/SPRAY valve between
• It is safe to change or replace the spray tip.
NOTE: If the pressure indicator begins blinking yellow
5
lock to the locked position.
pressure control knob to the OFF
position in the black zone.
instructed by the tip guard or tip
manuals.
WARNING
turning the pressure control knob to the "Min PSI" setting
in the yellow zone.
knob slowly clockwise toward the green zone and test the
spray pattern on a piece of cardboard. Adjust the
pressure control knob until the spray from the gun is
completely atomized.
atomize the paint will cause premature tip wear
and additional overspray.
Blinking Yellow
0–200 PSI
Solid Yellow
200–1800 PSI
Solid Green
1800–3300 PSI
Motor Running
Indicator
Programmer
Port
positions.
when the pressure control knob is set at a
higher pressure and the PRIME/SPRAY valve is
in the SPRAY position, either the spray tip is
worn or the sprayer is in need of service/repair.
Trigger lock
in locked position.
Pressure Indicator
Motor Running
Indicator
Programmer
Port