Timer Programming - Toshiba D-R560KU Owner's Manual

Use [K / L] to enter the date, then
3
press [B].

Timer Programming

Date Start
New Program
Date
JAN/02
CH
DTV125- 1
JAN/01
Daily
MON-SAT
MON-FRI
SAT
FRI
SUN
JAN/31
Use [K / L / { / B] or [the Number
4
buttons] to enter the start and end
time, then press [B].
New Program
Date
JAN/02 12 : 00AM
CH
DTV125- 1
• You cannot make a program which recording
time exceeds 12 hours.
Use [K / L] to select analog ("- - -") /
5
digital ("DTV") mode or external
input (L1 / L2), then press [B].
New Program
Date
JAN/02 12 : 00AM
CH
L1
To record from external input (e.g., cable/
satellite box), select L1 or L2.
Use [K / L] to select the channel number to
record.
For digital mode, select both major and minor
channels. Refer to "How to select a channel
number for the timer recording" on page 50
for more details.
e.g.) analog mode
New Program
Date
JAN/02 12 : 00AM
CH
10
E7M70UD_D-R560KU_EN.indd 49 E7M70UD_D-R560KU_EN.indd 49
TIMER RECORDING
TUE JAN/01 10:00AM
End CH
Start End
- - : - - - - : - -
Mode
SP
SP 2 : 00
1/1
When pressing [L] at
the current date, the
date will change as
follows.
e.g.) January 1st
Start End
- - : - -
Mode
SP
SP 2 : 00
1/1
Start End
1 : 00AM
Mode
SP
SP 1 : 00
1/1
Start End
1 : 00AM
Mode
SP
SP 1 : 00
1/1
e.g.) digital mode
New Program
Date Start
JAN/02 12 : 00AM
CH Mode
DTV125- 1 SP
Use [K / L] to select a recording
6
mode.
New Program
Date Start
JAN/02 12 : 00AM
CH Mode
DTV125- 1 SP
Refer to "Recording Mode" on page 43.
• You can check the remaining recordable space
of the disc when you select the recording
mode.
Date Start
JAN/02 12 : 00AM
CH Mode
DTV125- 1 SP
Auto recording mode select...
When "Auto" is selected as a recording mode, the unit
calculates how much time is available on the disc and
determines the appropriate recording mode to
complete recording the program.
New Program
Date Start
JAN/02 12 : 00AM
CH Mode
DTV125- 1 Auto
• "Auto" is only available for one program in the timer
program list.
• The recording may be cut short, when the available
recording space of the disc is too limited.
7
Press [ENTER] when all items are
entered.
Your program setting will be stored.
• To set another program, repeat steps 2 to 7.
• To exit, press [TIMER PROG.] or [SETUP].
• When 2 or more programs are overlapped,
"Timer program overlapped" appears, and the
overlapped program will be displayed in blue.
To correct the timer program refer to
"Checking, canceling, or correcting the timer
programming information" on page 51.
8
Press [I/y ON/STANDBY] to set a
timer programming.
will appear on the front panel display, while this
unit waits to make the recording.
End
1 : 00AM
SP 1 : 00
1/1
End
1 : 00AM
SP 1 : 00
1/1
End
1 : 00AM
SP 1 : 00
End
1 : 00AM
Auto 1 : 00
1/1
EN EN 49 49
2007/12/17 11:12:10 2007/12/17 11:12:10