The Default Setting Menu - Toshiba TDP-T250U Owner's Manual

Using the menus (Continued)

■ The default setting menu

This menu shows placement status and other settings.
Item
Projection Sets projection mode in accordance with Placement Style.
mode
(Standard)
Blackboard When projecting on a non-screen surface, select a color in accordance
mode with the projecting surface.
Press . Switch with
No signal Set the time to wait for the power to be turned off after signal input
power off stops or the last operation.
Press . Switch with
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Auto input Set whether the input with signals is only selected or not.
search
Power on
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual
Lamp power
Sets the lamp power.
Fan mode
Sets the cooling fan speed.
Remote control
When two or more projectors are used and controlled by the remote
code
control respectively, this menu sets the code for the projector and the
remote control.
[ :Enter setting mode]
from 1, 2, 3, 4] [
Press [Cancel] to return.
Key lock
Lock the control panel buttons.
[ :Enter setting mode]
On/Off] [ :Confirm]
Press [Cancel] to return.
Reset all
Press .
Resets all adjustments and settings to their factory settings.
Password
Password function
p.36
When [Password] is [On], the Password Setting screen is displayed.
Detailed description
[Blackboard mode]
Projects the image in colors more like projecting on a screen.
Precaution
The projected image may differ depending on the type, color, and material of the
blackboard and wall even if the selected color is the same as the projected screen.
Description
p.22
(Mounted (Rear mounted
(Rear)
from ceiling)
from ceiling)
and . Off/Green/Black/Brown/Blue/Beige
and .
On
Low Standard
Standard
[ : Select item] [ : Select
:Confirm] [ :Select OK to end]
[ : Select item] [ : Select
[ :Select OK to end]
Yes
On
44
[Auto input Search]
[On]: Automatically searches the signals that
can be projected, and switches input
from the connected device that outputs
the signals each time the INPUT button
is pressed. The input from the connected
device that outputs no signals is skipped.
[Off]: Displays the Switch input menu.
Toggle with
button (The input without signals can be
selected.)
[Power on]
Note that if [Power on] is set to [Auto], then if the main power switch is ON when
Off
power is restored after a power outage, the projector will come on.
[Lamp power]
Auto
When [Lamp power] is set to [Low], the screen becomes a little darker, but the
cooling fan noise gets quieter.
[Fan mode]
High
Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to
use the projector, for example, at high altitude (over 1,500 meters above sea level).
[Remote control code]
Sets a remote control code from 4 types. You can set each code respectively for up
to 4 projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
• You cannot operate the remote control if the codes of the projector and the
remote control do not match.
Remote control code setting for remote control
Remove the battery cover and set the same remote control code switch as the
No
projector.
p.16 (Use a screwdriver with thin tip to set.)
Off
[Key lock]
Protect from operating errors by locking on the control panel buttons of the
projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done.
• To release the key lock, press the control panel's RETURN button for 10 seconds.
The key lock is released with a beep sound.
Switch input menu
Switch input
Computer (1) (digital)
Y/P /P (1) (digital)
B R
Computer (1) (analog)
Y/P /P (1) (analog)
B R
Computer (2)
Y/P /P (2)
B R
Computer (3)
buttons and press
Y/P /P (3)
B R
Video
S-video
/ shows whether signal is
input or not.
45