Page 1
OPERATION AND PARTS MANUAL MC-64S MC-64P CONCRETE MIXERS Revision #7 (09/15/11) www.discount-equipment.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Page 2
One of our experienced staff members will get back to you with a quote for the right part that your machine needs. We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mayco, Toro/Stone, Diamond Products, Magnum, Airman, Mustang, Power Blanket, Nifty Lift, Atlas Copco,...
Gas Engine Mounting Plate Asasembly .... 46-47 Terms and Conditions of Sale ....... 114 Electric Motor Mounting Plate Asasembly ..48-49 Specification and part number NOTE are subject to change without notice PAGE 4 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
Symbols which appear throughout this manual, and will be surrounding environment could referenced in conjunction with Safety Message Alert Symbols. NOTE be damaged if you do not follow instructions. PAGE 8 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
■ NEVER! place hands inside the drum while the drum is the equipment and/or injury to user may result. rotating. ■ Manufacturer does not assume responsibility for any accident due to equipment modifications. MC-64P/S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #7 (09/15/11) — PAGE 9...
Page 9
■ High Temperatures – Always stop engine and allow the engine to cool before adding fuel, oil or performing service and maintenance functions. Contact with hot components can cause serious burns. PAGE 10 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
Machine Safety Decals The Multiquip MC-64P/S mixers are equipped with a number of safety decals (Figure 1A). These decals are provided for operator safety and maintenance information. The illustration below and on the next page shows these decals as they appear on the machine.
Page 11
Table 5. Remember cable distance affects the current-voltage capacity of the extension cable. ) . s , s t . c t PAGE 12 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
The MC-64P/S concrete mixers are shipped with the handwheel detached. Attach the handwheel to the mixer as shown in Figure 4. Figure 4. Handwheel Assembly MC-64P/S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #7 (09/15/11) — PAGE 15...
3. As a minimum, use a 1/2-inch bolt and nylock nut grade position (gasoline models only). 5 when securing either tow bar to the towing vehicle, PAGE 16 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
1/2-inch bolt through tow bar and frame. vehicle. Secure tow bar to frame with 1/2-inch nylock nut. Tighten to 40 ft.-lbs. Figure 5. Tow Bar and Safety Chain Installation MC-64P/S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #7 (09/15/11) — PAGE 17...
. t f . t f . t f . t f a t l PAGE 18 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
Page 18
MC-64P/S CONCRETE MIXER — ELECTRIC MOTOR Figure 7. Single Phase Electric Motor with 12 inch Pigtail Cable MC-64P/S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #7 (09/15/11) — PAGE 19...
Page 19
Check the zerk grease fittings (Figure 27) as shown in the maintenance section of this manual. These grease fittings lubricate the handwheel and the yoke mechanism . Figure 9. Engine Oil Dipstick (Oil Level) PAGE 20 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
Page 20
Move the throttle lever (Figure 12) away from the slow position, about 1/3 of the way toward the fast position. Figure 15. Starter Grip Figure 12. Throttle Lever MC-64P/S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #7 (09/15/11) — PAGE 21...
NOTE extension cord so that it lays flat and is not curled underneath the mixer. Figure 18. Electric Motor ON/OFF Switch (ON Position) PAGE 22 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
(OFF Position) Disconnect the electric motor's extension cord from its power source. Figure 20. Filling Mixing Drum Clean drum of all debris and foreign matter. MC-64P/S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #7 (09/15/11) — PAGE 23...
Page 23
) 3 ( a i c i t a r e t t n i r e t . s l PAGE 24 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
For thorough mix and longer drum life, always wash drum out after each use. NEVER! pour or spray water over the engine or electric Figure 28. Grease Fittings Electric Motor motor. PAGE 26 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
Page 26
CAUTION: ALWAYS wear safety glasses NOTE when removing or installing force fitted parts. Failure to comply may result in serious injury. Figure 30. Suspension Components MC-64P/S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #7 (09/15/11) — PAGE 27...
Page 27
Place the mixing drum in the down position (mouth facing downward). Cover the mixer and place it a clean dry area, that is protected from harsh elements. Figure 31. Wheel Lug Nuts Tightening Sequence PAGE 28 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
Multiquip. Other entries will for sale through Multiquip. be clarified in the “Remarks” Column. PAGE 32 —MC-64P/S CONCRETE MIXERS — OPERATION & PARTS MANUAL — REV. #7 (09/15/11)
Page 112
One of our experienced staff members will get back to you with a quote for the right part that your machine needs. We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mayco, Toro/Stone, Diamond Products, Magnum, Airman, Mustang, Power Blanket, Nifty Lift, Atlas Copco,...