Table of Contents
Advertisement
KX-FP362CX
Code
593
Time between CED and 300bps
594
Overseas DIS detection select
595
Receive error limit value set
596
Transmit level set
598
Receiving sensitivity
599
ECM frame size
717
Transmit speed selection
718
Receive speed selection
722
Redial tone detect
731
CPC mode
732
AUTO disconnect cancel time
745
Power ON film feed
763
CNG detect time for friendly
reception
771
T1 timer
774
T4 timer
775
Monitoring of message transfer
784
Voice prompt test
815
Sensor & Vox check
841
Digital SP-phone check
852
Print test pattern
853
Top margin
874
DTMFontime
875
DTMFofftime
880
History list
881
Journal 2 list
882
Journal 3 list
Function
Set Value
1:75 msec
2:500 msec
3:1 sec
1:detects at
the 1st time
2:detects at
the 2st time
X Number of
times
X dBm
43= -43 dBm
1:256 byte
2:64 byte
1:14400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1:14400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1:ON 2:OFF
1:A 2:B 3:OFF
1:350 ms
2:1.8 sec
3:OFF
1:ON 2:OFF
1:10 sec
2:20 sec
3:30 sec
1:35 sec
2:60 sec
X 100 msec
1:ON 2:OFF
060~200ms
060~200ms
Effective
Default
Range
1~3
1
See Symptom/Countermeasure Table for long
distance and international calls in THE UNIT CAN
COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS (P.78).
Refer to RECEIVE PROBLEM (P.77) and THE
UNIT CAN COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS (P.78).
1, 2
1
See Symptom/Countermeasure Table for long
distance and international calls in THE UNIT CAN
COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS (P.78).
Refer to SOMETIME THERE IS A TRANSMIT
PROBLEM (P.76) and THE UNIT CAN COPY,
BUT CANNOT EITHER TRANSMIT/RECEIVE
LONG DISTANCE OR INTERNATIONL
COMMUNICATIONS (P.78).
001~999
100
Sets the number of acceptable error lines when
the FAX reconstructs the received data. Refer to
RECEIVE PROBLEM (P.77).
- 15~00
-10
Selects the FAX transmission level. Refer to
SOMETIME THERE IS A TRANSMIT PROBLEM
(P.76)and RECEIVE PROBLEM (P.77).
20~48
40
Used when there is an error problem. Refer to
THE UNIT CAN COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS (P.78).
1, 2
1
1~6
1
Adjusts the speed to start training during FAX
transmission. Refer to SOMETIME THERE IS A
TRANSMIT PROBLEM (P.76) and THE UNIT
CAN COPY, BUT THE TRANSMISSION AND
RECEPTION IMAGE ARE INCORRECT (P.81).
1~6
1
Adjusts the speed to start training during FAX
reception. Refer to RECEIVE PROBLEM (P.77)
and THE UNIT CAN COPY, BUT THE
TRANSMISSION AND RECEPTION IMAGE ARE
INCORRECT (P.81).
1, 2
1
Sets the tone detection mode after redialing.
1~3
1
Sets the CPC signal detection mode from the
converter.
1~3
1
"Set to "2" when the auto disconnect circuit
operates and cuts the line."
1, 2
1
When the power is turned on, the film is wound to
take up any slack.
1~3
3
Selects the CNG detection tone of friendly
reception.
1, 2
1
Sets a higher value when the response from the
other party needs more time during FAX
transmission.
00~99
00
Use this function when delay occurs in the line
and communication (ex. Mobile comm) does not
work well.
1, 2
2
If set to ON a message can be monitored from
this unit´s SP-PHONE when transferring a
message.
You can hear the voice prompt from speaker after
pressing "START" key.
See TEST FUNCTIONS (P.49).
See DIGITAL SPEAKERPHONE (P.106).
See TEST FUNCTIONS (P.49).
1~9
5
060~200
090
060~200
085
See HISTORY (P.57).
See PRINTOUT EXAMPLE (P.94).
See PRINTOUT EXAMPLE (P.94).
48
Remarks
----------
----------
----------
----------
Advertisement
Table of Contents
Troubleshooting
